Craftsman 919.763010 owner manual Pump Oil, Changing Engine Oil

Page 12

Pressure Washer Maintenance

Check and Clean Inlet Screen: Examine inlet screen on pump inlet fitting. Clean if clogged replace if torn.

Check High Pressure Hose: High pressure hose can develop leaks from wear, kinking, abuse. Inspect hose each time before use. Check for cuts, leaks, abrasions or bulging of cover, damage or movement of couplings. If any of these conditions exist, replace hose immediately.

Check Chemical/Soap Hose: Examine the chemical/ soap hose and clean if clogged. Hose should fit tightly on pump fitting. Check for leaks and tears. Replace filter or hose if either is damaged.

Check Gun and Wand: Examine hose connection to gun making sure it is secure. Test trigger by pressing it and making sure it springs back into place when you release it.

Pump Oil

Pump oil level should be checked before each use.

Changing Pump Oil

Oil should be changed after the first 10 hours of opera-

tion. Subsequent changes after each 50 hours of opera- tion. To drain oil, simply remove oil plug with a adjust- able wrench. The oil plug is located at the bottom of the pump. Dispose of used oil. Properly remove pump oil fill plug. Add 30 weight non-detergent oil. Fill until oil level is at the mid point on the sight glass.

•Pull the trigger on the gun and hold.

•When the water supply is steady and constant, disengage trigger and refasten the wand extension.

Engine Maintenance

Oil

• Oil level should be checked prior to each use

or at least every 5 hours of operation. To check oil see Adding Engine Oil on page 9.

Changing Engine Oil

For a new engine, change oil after the first 5 hours of operation. Thereafter, change oil after every 50 hours of operation.

Change the oil while the engine is still warm. The oil will flow freely and carry away more impurities. Make sure the engine is level when filling, checking, or changing oil.

Change the oil as follows:

•To keep dirt, grass clippings, etc., out of the engine, clean the area around the drain plug and dipstick before removing it.

•Remove the oil drain plug and dipstick. Tilt the engine slightly towards the oil drain to obtain better drainage. Be sure to allow ample time for complete drainage.

Purge Pump of Air and Contaminants

To remove the air from the pump, follow these steps:

•Set up the pressure washer as described in Assembly section and connect the water supply.

•Remove the wand extension from the spray gun,

•Pull the trigger on the gun and hold.

To remove the contaminants from the pump, follow these steps:

•Set up the pressure washer as described in ASSEMBLY section, connect the water supply.

•Remove the wand extension from the spray gun.

•Start the engine according to instructions in the OPERATION section.

•Reinstall the drain plug. Make sure it is tightened securely.

•Fill the crankcase with new oil of the proper type, to the Full mark on the dipstick. Always check the level with the dipstick before adding more oil.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Craftsman Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.ATable of Contents HOW to Prevent IT Death or serious injuryResult in minor or moderate Hazard Risk of Explosion Or FireHazard Risk of Unsafe Operation What can Happen Risk of Fluid InjectionHazard What Can Happen Serious pump damage Checklist BoltKnow Your High Pressure Washer CHOKE- Lever used for starting unitHow To Use Your Pressure Washer Using Soaps/ChemicalsStopping Your Pressure Washer Before Starting the EngineAdding Pump Oil Engine OilTo Start Your Pressure Washer Maintenance Task Customer Responsibilities TablePressure EnginePump Oil Changing Engine OilReinstalltheoilfill caporplugandtightensecurely Clean and Replace Spark PlugNozzle Maintenance Dual Lance CarburetorPreparing Pressure Washer for Storage Engine Preparation Pump PreparationSymptom SolutionCause Part Description Description QTY=KIT \ C 900 KEY# Partnumber DescriptionI16A 22A 868I 1026 17A 843Q 663 211 281 232 202 356A 347634 255 255A957 642 346A 535 161 971 176 819863A 819 20S 988\ 182 246 601 C710224 Flywheel T1036 Emission Label KIT f 515A 1A4 Intake manifold Improper maintenance Sears RIiFTSMRNo GARANTiA Limitada DE UN Aiio Para Lavadoras Craftsman DE Alta PresinGARANTiA Limitada DE UN Aiio DEL Motor Craftsman Riesgo QUE Puede SucederInstrucciones Riesgo QUE Puede Suceder Como Prevenirlo CAP Familiarizarse con la Lavadora de Presi6n ASAComo usar la Lavadora de Presibn NotaApagado de la Lavadora de Presi6n Antes de Arrancar el MotorAgregar Aceite a la Bomba Aceite del MotorPara Arrancar la Lavadora a Presi6n Responsabilidades DEL Propietario Especificaciones Del EquipoRecomendaciones Generales Cambio de Aceite de la Bomba Mantenimiento del Motor AceiteCambio de Aceite del Motor Cambiar el aceite de la siguiente formaMantenimiento del Filtro de Aire Para limpiar el filtro de aire seguir estos pasosLimpiar y Reemplazar la Bujia Carburador Preparacibn de la Unidad para su AlmacenamientoPreparacibn del Motor Mantenimiento de la Boquilla Tubo Aplicador DualSiNTOMA Causa SolucionPara Liste DE Partes VEA LA Pagina Version EN Ingles 6o ID Version Para Liste DE Partes VEA LA Pagina Version EN Ingles Craftsman 3000 PSI Maquina Lavadora DE Alta Presion Part

919.763010 specifications

The Craftsman 919.763010 is a versatile and reliable air compressor designed for both professional and DIY users. This model is noted for its robust construction and user-friendly features, making it an essential tool for a wide range of applications, from powering pneumatic tools to inflating tires.

One of the main features of the Craftsman 919.763010 is its impressive performance specifications. It typically boasts a tank capacity of 6 gallons, which is ideal for a variety of tasks. The compressor's maximum pressure is generally rated at around 150 PSI, allowing users to operate tools that require higher pressure levels efficiently. This means you can power nail guns, spray painters, and air wrenches without worrying about the compressor running out of power.

The Craftsman 919.763010 is powered by a 1.5-horsepower motor that ensures reliable performance. It features an oil-free pump, which significantly reduces maintenance requirements while ensuring that you can use it in various settings without the concern of oil spills. This is particularly useful for indoor applications where cleanliness is a priority.

One of the standout technologies incorporated into this model is its low noise operation. Typically producing around 78 decibels, it is quieter than many other compressors in its class, making it suitable for home use where noise might be a concern. This makes it user-friendly as it minimizes disturbances, whether you are working on a home improvement project or engaging in hobby work.

The Craftsman 919.763010 also features a convenient design with a lightweight body, which enhances its portability. With rubber grip handles and a sturdy wheel base, moving it around the job site or storage is hassle-free. Additionally, the quick-connect air fittings allow for easy setups, letting users switch between different air tools rapidly.

In terms of safety, this compressor often includes essential features like thermal overload protection, preventing the motor from overheating, further enhancing its longevity. The overall build quality reflects a commitment to durability, making it a worthwhile investment for users who require a reliable air compressor for various applications.

Overall, the Craftsman 919.763010 stands out as a well-rounded air compressor, balancing power, efficiency, and convenience, making it a recommended choice for both amateur and professional users alike.
Top Page Image Contents