Craftsman 919.763010 Stopping Your Pressure Washer, Before Starting the Engine, Adding Pump Oil

Page 9

Stopping Your Pressure Washer

A CAUTION: Do not run pump without the water supply connected and turned on. Failure to do so will result in pump damage.

•To turn pressure washer off place the on/off switch to the off position.

•Simply shutting OFF engine will not release pressure in the system. Squeeze the trigger on the spray gun for about 3 seconds to relieve pressure. Spray stream will decrease in length.

IMPORTANT: This unit is equipped with a thermal relief valve. If unit is allowed to run for several minutes

without pressing the trigger on the spray gun, several drops of water may be released through this valve to cool the unit. This small amount of water will drip from the bottom of the pump.

BEFORE STARTING THE ENGINE

To operate the engine you will need to do the following.

,& CAUTION: Always check engine oil level before

every start. Running engine low of oil or out of oil could result in serious damage.

_, CAUTION: Always check pump oil level before every start. Running pump low on oil could result in pump damage.

Adding Pump Oil

Before running the high pressure washer, check the pump oil level by viewing the sight glass on the side of the pump. When properly filled, the oil will be at the half way point marked by the two triangles. Your pressure washer pump is shipped with oil. Add only if oil level is lower than the half way point on the sight glass. Do not overfill. Use 30 weight non-detergent oil if necessary.

ACAUTION: Do Not use engine oil that has been shipped with your unit in your pump. Engine oil is detergent and your pump uses a non-detergent oil. Detergent oil can cause damage to your pump.

Engine Oil

Your unit has been shipped without oil in the engine. A bottle of SAE 30 weight oil is included in the carton. Remove oil dip stick located on the side of

engine. The oil dip stick is clearly marked with a lines that tells you when unit has enough oil. Do not fill above this point. Pour slowly.

NOTE: When adding oil to the engine crankcase, use

a high quality detergent oil classified "For Service SF, SG, SH rated SAE 30 weight. Use no special addi- tives. Select the oil'sviscosity grade according to your expected operating temperatures.

SAE Viscosity Grades

ll_'Ifl_]dl

TARTENG TEMPERATURERANGEANTICIPATED BEFORENEXT OIL GHANGE

Air cooled engines run hotter than automotive engines. The use of multi-viscosity oil such as (10W-30, etc.) in ambient temperatures above 40°F (4°C) will result in

higher than normal oil consumption, if multi-viscosity oil is used, check the oil level more frequently to

prevent any posssible engine damage due to lack of lubrication.

Use of SAE30 oil below 40°F (4°C) will result in hard starting and possible engine damage due to inad- equate lubrication.

Gasoline

Your pressure washer engine is 4 cycle. Use unleaded fuel only.

_, CAUTION: Do not overfill the fuel tank. Always allow room for fuel expansion.

_,WARNING: Never fill fuel tank indoors. Never fill fuel tank when engine is running or hot. Do not smoke or have open flame when filling fuel tank.

Use clean, fresh, regular unleaded gasoline with a minimum of 85 octane. Do not mix oil with gasoline. If unleaded fuel is not avalab[e, leaded fuel may be used.

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A CraftsmanTable of Contents Death or serious injury HOW to Prevent ITResult in minor or moderate Hazard Risk of Explosion Or FireRisk of Fluid Injection Hazard Risk of Unsafe Operation What can HappenHazard What Can Happen Bolt Serious pump damage ChecklistCHOKE- Lever used for starting unit Know Your High Pressure WasherUsing Soaps/Chemicals How To Use Your Pressure WasherBefore Starting the Engine Stopping Your Pressure WasherAdding Pump Oil Engine OilTo Start Your Pressure Washer Customer Responsibilities Table Maintenance TaskPressure EngineChanging Engine Oil Pump OilClean and Replace Spark Plug Reinstalltheoilfill caporplugandtightensecurelyCarburetor Nozzle Maintenance Dual LancePreparing Pressure Washer for Storage Engine Preparation Pump PreparationSymptom SolutionCause Part Description Description QTY=KIT \ C KEY# Partnumber Description 900I16A 22A 868I 1026 17A 232 202 356A 347 843Q 663 211 281255A 634 255957 642 346A 535 161 971 176 819863A 819 20S 988\ 182 601 C 246710224 Flywheel T1036 Emission Label KIT f 515A 1A4 Intake manifold Improper maintenance Sears RIiFTSMRNo GARANTiA Limitada DE UN Aiio Para Lavadoras Craftsman DE Alta PresinGARANTiA Limitada DE UN Aiio DEL Motor Craftsman QUE Puede Suceder RiesgoInstrucciones Riesgo QUE Puede Suceder Como Prevenirlo CAP ASA Familiarizarse con la Lavadora de Presi6nNota Como usar la Lavadora de PresibnAntes de Arrancar el Motor Apagado de la Lavadora de Presi6nAgregar Aceite a la Bomba Aceite del MotorPara Arrancar la Lavadora a Presi6n Responsabilidades DEL Propietario Especificaciones Del EquipoRecomendaciones Generales Mantenimiento del Motor Aceite Cambio de Aceite de la BombaCambio de Aceite del Motor Cambiar el aceite de la siguiente formaMantenimiento del Filtro de Aire Para limpiar el filtro de aire seguir estos pasosLimpiar y Reemplazar la Bujia Preparacibn de la Unidad para su Almacenamiento CarburadorPreparacibn del Motor Mantenimiento de la Boquilla Tubo Aplicador DualCausa Solucion SiNTOMAPara Liste DE Partes VEA LA Pagina Version EN Ingles 6o ID Version Para Liste DE Partes VEA LA Pagina Version EN Ingles Craftsman 3000 PSI Maquina Lavadora DE Alta Presion Part

919.763010 specifications

The Craftsman 919.763010 is a versatile and reliable air compressor designed for both professional and DIY users. This model is noted for its robust construction and user-friendly features, making it an essential tool for a wide range of applications, from powering pneumatic tools to inflating tires.

One of the main features of the Craftsman 919.763010 is its impressive performance specifications. It typically boasts a tank capacity of 6 gallons, which is ideal for a variety of tasks. The compressor's maximum pressure is generally rated at around 150 PSI, allowing users to operate tools that require higher pressure levels efficiently. This means you can power nail guns, spray painters, and air wrenches without worrying about the compressor running out of power.

The Craftsman 919.763010 is powered by a 1.5-horsepower motor that ensures reliable performance. It features an oil-free pump, which significantly reduces maintenance requirements while ensuring that you can use it in various settings without the concern of oil spills. This is particularly useful for indoor applications where cleanliness is a priority.

One of the standout technologies incorporated into this model is its low noise operation. Typically producing around 78 decibels, it is quieter than many other compressors in its class, making it suitable for home use where noise might be a concern. This makes it user-friendly as it minimizes disturbances, whether you are working on a home improvement project or engaging in hobby work.

The Craftsman 919.763010 also features a convenient design with a lightweight body, which enhances its portability. With rubber grip handles and a sturdy wheel base, moving it around the job site or storage is hassle-free. Additionally, the quick-connect air fittings allow for easy setups, letting users switch between different air tools rapidly.

In terms of safety, this compressor often includes essential features like thermal overload protection, preventing the motor from overheating, further enhancing its longevity. The overall build quality reflects a commitment to durability, making it a worthwhile investment for users who require a reliable air compressor for various applications.

Overall, the Craftsman 919.763010 stands out as a well-rounded air compressor, balancing power, efficiency, and convenience, making it a recommended choice for both amateur and professional users alike.
Top Page Image Contents