Delta DTH2450 instruction manual Pressure Washer, Pressure Adjustments

Page 8

PRESSURE WASHER

TERMINOLOGY (cont'd)

Bypass Mode: Allows water to re-circulate within pump when the gun trigger is not pulled.

Allowing the unit to run for more than

two minutes without the gun trigger pulled could cause overheating and damage to the pump.

Chemical Injection System: Mixes cleaners or cleaning solvents with the water to improve cleaning effectiveness.

Water Supply: All pressure washers must have a source of water. The minimum requirements for a water supply are 20 PSI and 5 gallons per minute.

PRESSURE WASHER OPERATING FEATURES

PRESSURE ADJUSTMENTS

The pressure setting is preset at the factory to achieve optimum pressure and cleaning. If you need to lower the pressure, it can be accomplished by these methods.

1.Back away from the surface to be cleaned. The further away you are, the less the pressure will be on the surface to be cleaned.

2.Rotate the nozzle at the end of the multi-adjustable spray wand to widen the fan spray. The wider fan spray will minimize the pressure on the surface to be cleaned.

DO NOT attempt to

increase pump

pressure. A higher pressure setting than the factory set pressure may damage pump.

READ AND UNDERSTAND ALL WARNINGS BEFORE STARTING UNIT

When using the high pressure setting, DO NOT allow the high pressure spray to come in contact with unprotected skin,

eyes, or with any pets or animals. Serious injury can occur.

Your washer operates at fluid pressures and velocities high enough to penetrate human and animal flesh, which could result in amputation or other serious injury. Leaks caused by loose fittings or worn or damaged hoses can result in injection injuries. DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a physician immediately!

NEVER fill fuel tank when engine is running or hot. Do not smoke when filling fuel tank.

NEVER fill fuel tank completely. Fill tank to 1/2" below bottom of filler neck to provide space for fuel expansion. Wipe any fuel spillage from engine and equipment before starting engine.

NEVER run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon monoxide, an odorless and deadly gas.

DO NOT let hoses come in contact with very hot engine muffler during or immediately after use of your pressure washer. Damage to hoses from contact with hot engine surfaces will NOT be covered by warranty.

NEVER pull water supply hose to move pressure washer. This could damage hose and/or pump inlet.

DO NOT use hot water, use cold water only.

NEVER turn water supply off while pressure washer engine is running or damage to pump will result.

DO NOT stop spraying water for more than two minutes at a time. Pump operates in bypass mode when spray gun trigger is not pressed. If pump is left in bypass mode for more than two minutes internal components of the pump can be damaged.

If you do not understand these precautions, please call 1-866-422-4286to speak to a service representative for further instructions.

A00521

8- ENG

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Structioin N M Anual Risk of Explosion or Fire Consumer Safety InformationImportant Safety Instructions Risk to Breathing Risk of Fluid InjectionRisk of HOT Surfaces Risk of Chemical BurnRisk of Electrical Shock Risk of Unsafe Operation Risk of Injury from SprayCarton Contents Assembly InstructionsOperating Instructions Basic Elements of a Pressure WasherBasic Elements of AN Engine Pressure Washer TerminologyRead and Understand ALL Warnings Before Starting Unit Pressure AdjustmentsPressure Washer HOW to Apply Chemicals and Cleaning Solvents HOW to USE Spray WandStarting Shutting DownMaintenance Nozzle CleaningHOW to Clean the Water Inlet Filter Engine PumpPressure Washer StorageEngine Causecorrection Trouble Shooting GuideProblem Problem Cause Correction ChemicalsENG A00521 Warranty

DTH2450 specifications

The Delta DTH2450 is a cutting-edge hammer drill known for its robust performance and versatility, making it a popular choice among both professionals and enthusiasts in the construction and DIY sectors. This model incorporates advanced engineering and technologies that elevate its efficiency and usability, ensuring it meets the demands of various tasks.

One of the standout features of the Delta DTH2450 is its powerful motor, which delivers a substantial amount of torque. This motor enables the drill to perform a wide range of applications, from heavy-duty drilling in concrete to more delicate tasks in wood and metal. The hammer drill function allows for effective penetration into hard materials, making it ideal for anchoring, drilling holes for rebar, or installing fixtures.

The DTH2450 boasts a variable speed control, allowing users to adjust the speed according to the specific material being worked on. This feature enhances its versatility as it can cater to different materials and project requirements. Additionally, the drill is equipped with a two-speed gearbox, which further optimizes its capabilities by providing options for high speed or high torque, depending on the task at hand.

Another notable characteristic of the Delta DTH2450 is its ergonomic design. The lightweight construction combined with an optimally designed handle ensures a comfortable grip while reducing user fatigue during extended use. This design is complemented by a built-in vibration reduction system, which minimizes the impact felt by the user, leading to improved control and precision.

Safety features are also a priority with the Delta DTH2450. It includes a safety clutch that prevents the drill from jamming during operation, protecting both the user and the tool. Moreover, the model features a robust construction with high-quality materials, ensuring durability and longevity in demanding work environments.

In terms of connectivity, the Delta DTH2450 is compatible with a range of accessories and attachments, expanding its functionality even further. Whether you need to switch to different drill bits or use it with various attachments for specific tasks, this drill is designed to adapt.

Overall, the Delta DTH2450 is a powerful, versatile, and user-friendly hammer drill, making it an excellent addition to any tool collection. Its combination of advanced features, ergonomic design, and safety functions positions it as a top choice for anyone looking to complete a variety of drilling tasks effectively.
Top Page Image Contents