Delta DTH2450 instruction manual Trouble Shooting Guide, Problem, Causecorrection

Page 13

PROBLEM

TROUBLE SHOOTING GUIDE

CAUSECORRECTION

Engine will not start (see Engine Manual for further engine troubleshooting)

No or low pressure (initial use)

No fuel.

Pressure builds up after two pulls on the recoil starter or after initial use.

Choke lever in the “No Choke” position.

Spark plug wire not attached.

Engine ON/OFF switch in OFF position.

Choke lever in the “Choke” position on a “hot” engine or an engine that has been exposed to thermal heat for a long period of time.

Fuel valve closed.

Spray wand not in high pressure.

Low water supply.

Leak at high pressure hose fitting.

Nozzle obstructed.

Water filter screen clogged.

Defective E-Z start valve.

Air in hose.

Choke lever in the “Choke” position.

High pressure hose is too long.

Add Fuel.

Squeeze gun trigger to relieve pressure.

Move choke to the “Choke” position.

Attach spark plug wire.

Place engine ON/OFF switch in on position.

Move choke to the “No Choke” position.

Move the fuel valve lever to the “Open” position.

See How to Use Spray Wand instructions in the Operation section.

Water supply must be at least 5 GPM @ 20 PSI.

Tighten fitting. Apply sealant tape if necessary.

See Nozzle Cleaning instructions in the Maintenance section.

Remove and clean filter.

Check with Authorized Warranty Service Center (AWSC.)

Turn off the engine, then the water source. Disconnect the water source from the pump inlet and turn the water source on to remove all air from the hose. When there is a steady stream of water present, turn water source off. Re-connect water source to pump inlet and turn on water source. Squeeze trigger to re- move remaining air.

Move choke to the “No Choke” position.

Use high pressure hose under 100 feet.

13- ENG

A00521

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Structioin N M Anual Important Safety Instructions Consumer Safety InformationRisk of Explosion or Fire Risk of Fluid Injection Risk to BreathingRisk of Electrical Shock Risk of Chemical BurnRisk of HOT Surfaces Risk of Injury from Spray Risk of Unsafe OperationAssembly Instructions Carton ContentsBasic Elements of a Pressure Washer Operating InstructionsBasic Elements of AN Engine Pressure Washer TerminologyPressure Washer Pressure AdjustmentsRead and Understand ALL Warnings Before Starting Unit HOW to USE Spray Wand HOW to Apply Chemicals and Cleaning SolventsShutting Down StartingNozzle Cleaning MaintenanceHOW to Clean the Water Inlet Filter Engine PumpEngine StoragePressure Washer Problem Trouble Shooting GuideCausecorrection Chemicals Problem Cause CorrectionENG A00521 Warranty

DTH2450 specifications

The Delta DTH2450 is a cutting-edge hammer drill known for its robust performance and versatility, making it a popular choice among both professionals and enthusiasts in the construction and DIY sectors. This model incorporates advanced engineering and technologies that elevate its efficiency and usability, ensuring it meets the demands of various tasks.

One of the standout features of the Delta DTH2450 is its powerful motor, which delivers a substantial amount of torque. This motor enables the drill to perform a wide range of applications, from heavy-duty drilling in concrete to more delicate tasks in wood and metal. The hammer drill function allows for effective penetration into hard materials, making it ideal for anchoring, drilling holes for rebar, or installing fixtures.

The DTH2450 boasts a variable speed control, allowing users to adjust the speed according to the specific material being worked on. This feature enhances its versatility as it can cater to different materials and project requirements. Additionally, the drill is equipped with a two-speed gearbox, which further optimizes its capabilities by providing options for high speed or high torque, depending on the task at hand.

Another notable characteristic of the Delta DTH2450 is its ergonomic design. The lightweight construction combined with an optimally designed handle ensures a comfortable grip while reducing user fatigue during extended use. This design is complemented by a built-in vibration reduction system, which minimizes the impact felt by the user, leading to improved control and precision.

Safety features are also a priority with the Delta DTH2450. It includes a safety clutch that prevents the drill from jamming during operation, protecting both the user and the tool. Moreover, the model features a robust construction with high-quality materials, ensuring durability and longevity in demanding work environments.

In terms of connectivity, the Delta DTH2450 is compatible with a range of accessories and attachments, expanding its functionality even further. Whether you need to switch to different drill bits or use it with various attachments for specific tasks, this drill is designed to adapt.

Overall, the Delta DTH2450 is a powerful, versatile, and user-friendly hammer drill, making it an excellent addition to any tool collection. Its combination of advanced features, ergonomic design, and safety functions positions it as a top choice for anyone looking to complete a variety of drilling tasks effectively.
Top Page Image Contents