Briggs & Stratton 20270 Maintenance Section, Specifications, General Maintenance Recommendations

Page 15

Maintenance Section

5

SPECIFICATIONS

Maximum Outlet Pressure . . . . . . . . . . . . . . . 3000 psi Maximum Flow Rate . . . . 2.7 gallons per minute (gpm) Detergent Use detergent approved for pressure washers

Water Supply . . . . . . . . . . . . . . . . Not to Exceed 100°F

Temperature

Automatic Cool . . . . . . . . . . . . . Will cycle when water

Down Systemreaches 125°-155°FShipping Weight . . . . . . . . . . . . . . . . . . . . . . . . . . .76 lbs.

GENERAL MAINTENANCE RECOMMENDATIONS

The pressure washer warranty does not cover items that have been subjected to operator abuse or negligence.To receive full value from the warranty, the operator must maintain the pressure washer as instructed in this manual.

NOTE: Should you have questions about replacing components on your pressure washer, please call 1-800-743-4115for assistance.

Some adjustments will need to be made periodically to properly maintain your pressure washer.

All maintenance in this manual and the engine operator’s manual should be made at least once each season.

Once a year you should clean or replace the spark plug, clean or replace the air filter and check the spray gun and nozzle extension assembly for wear.A new spark plug and clean air filter assure proper fuel-air mixture and help your engine run better and last longer. Please refer to your engine operator’s manual for more details.

If equipped with inflatable tires, keep the air pressure at the value marked on the tire or within 15 and 40 psi.

PRESSURE WASHER

MAINTENANCE

Check and Clean Inlet Screen

Examine the screen on the water inlet. Clean it if the screen is clogged or replace it if screen is damaged.

Check High Pressure Hose

The high pressure hose can develop leaks from wear, kinking, or abuse. Inspect the hose each time before using it. Check for cuts, leaks, abrasions or bulging of cover, damage or movement of couplings. If any of these conditions exist, replace the hose immediately.

WARNING

The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues, leading to serious injury and possible amputation.

NEVER repair high pressure hose. Replace it.

Replacement hose rating MUST exceed maximum pressure rating of unit.

Check Chemical Injection Hose

Examine the filter on the detergent tube and clean if clogged.The tube should fit tightly on the barbed fitting. Examine the tube for leaks or tears. Replace the filter or tube if either is damaged.

Check Gun and Nozzle Extension

Examine the hose connection to the spray gun and make sure it is secure.Test the trigger by pressing it and making sure it “springs back” into place when you release it. Put the trigger lock in the ON position and test the trigger. You should not be able to press the trigger.

Before Each Use

Check engine oil level.

Check water inlet screen for damage.

Check in-line filter for damage.

Check high pressure hose for leaks.

Check chemical injection hose and filter for damage.

Check spray gun and nozzle extension for leaks.

Rinse out garden hose to flush out debris.

Check In-Line Filter

Refer to Figure 18 and service the in-line filter if it becomes clogged, as follows:

Figure 18 — Clean In-Line Filter

Filter Screen

Nozzle Extension

O-ring

15

Image 15
Contents Operator’s Manual Manual del Operario Table of Contents Safety RulesEquipment Description Operate pressure washer only outdoors When Adding FuelUnintentional sparking can result in fire or electric shock High pressure spray may damage fragile items including glass Section Features and Controls Know Your Pressure WasherData Tag not shown, near rear of base plate Assembly Section AssemblyPreparing Pressure Washer for USE Add Engine Oil and Fuel AssemblyConnect Hose and Water Supply to Pump Checklist Before Starting EnginePressure Washer Location HOW to USE Your Pressure WasherHow to Start Your Pressure Washer Section OperationOperation How to Stop Your Pressure WasherHow to Use Accessory Tray How to Use ProjectPro Nozzle SystemFollow these instructions to change ProjectPro nozzles You must attach all hoses before you start the engine Cleaning and Applying DetergentThermal Relief Cleaning Detergent Siphoning TubePressure Washer Rinsing Automatic Cool Down SystemPressure Washer Maintenance Maintenance SectionSpecifications General Maintenance RecommendationsRing Maintenance MaintenanceEngine Maintenance Nozzle MaintenanceProtecting the Pump StoragePreparing the Unit for Storage Storing the EngineTroubleshooting TroubleshootingProblem Cause Correction Limited Warranty Conserve Estas Instrucciones Reglas de SeguridadCuando Añada Combustible Sección 1 Reglas de SeguridadCuando Pruebe LA Bujía DEL Motor Precaución Características y Controles Conozca SU Maquina Lavadora DE PresionExtensión para Boquillas con Conexión Rápida Le Montaje MontajePreparando EL Lavador a Alta Presión Para SU USO Lista de Revision Previa al Arranque del Motor Sección 3 MontajeAgregar Aceite al Motor y Gasolina Conecte la Manguera y el Suministro de Agua a la BombaCómo Darle Arranque a su Máquina Lavadora a Presión OperaciónCómo Usar SU Máquina Lavadora a Presión Ubicación del Lavadora a PresiónSección 4 Operación Cómo Detener su Máquina Lavadora a PresiónEl Pasador de la Seguridad La Presión Alta Utilización de la Bandeja de AccesoriosCómo Usar el Sistema de Boquillas ProjectPro La Presión BajaDetergentes caseros podrían dañar la bomba Limpieza y Aplicación del DetergentesPara aplicar el detergente, siga los siguientes pasos Enjuage de la Máquina Lavadora a PresiónLimpiando el Tubo Sistema de Enfriamiento Automático Alivio TérmicoMantenimiento DE LA Maquina Lavadora a Presion MantenimientoEspecificaciones Recomendaciones GeneralesMantenimiento de los Anillos O Sección 5 MantenimientoMantenimiento DEL Motor Mantenimiento de la BoquillaProteger la Bomba AlmacenamientoPreparando LA Unidad Para SU Almacenamiento Almacenando EL MotorReparacion DE Averias Diagnosticos de AveríasUso comercial Uso del consumidor