Briggs & Stratton 20270 operating instructions Assembly, Add Engine Oil and Fuel

Page 8

Section 3: Assembly

2.Insert carriage bolts through holes from outside of unit and attach a plastic knob from inside of unit (Figure 2). Tighten by hand.

Figure 2 — Secure Handle

3.Place accessory tray over holes on handle (viewing from front of unit). Push the tree clips into the holes until they sit flat against the accessory tray (Figure 3).

Figure 3 — Attach Accessory Tray to Handle

4.Insert multi–colored ProjectPro™ nozzles and other supplied accessories in spaces provided in accessory tray. See “How to Use Accessory Tray”.

Add Engine Oil and Fuel

• Place pressure washer on a level surface.

CAUTION

Any attempt to crank or start the engine before it has been properly filled with the recommended oil will result in equipment failure.

•Refer to engine operator’s manual for oil and fuel fill information.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

•Refer to engine operator’s manual and follow oil and fuel recommendations and instructions.

NOTE: Check oil often during engine break–in. Refer to engine operator’s manual for recommendations.

8

Image 8

Contents Operator’s Manual Manual del Operario Equipment Description Table of ContentsSafety Rules When Adding Fuel Operate pressure washer only outdoorsUnintentional sparking can result in fire or electric shock High pressure spray may damage fragile items including glass Data Tag not shown, near rear of base plate Section Features and ControlsKnow Your Pressure Washer Preparing Pressure Washer for USE Assembly SectionAssembly Assembly Add Engine Oil and FuelChecklist Before Starting Engine Connect Hose and Water Supply to PumpHOW to USE Your Pressure Washer How to Start Your Pressure WasherSection Operation Pressure Washer LocationHow to Stop Your Pressure Washer OperationFollow these instructions to change ProjectPro nozzles How to Use Accessory TrayHow to Use ProjectPro Nozzle System Cleaning and Applying Detergent You must attach all hoses before you start the engineCleaning Detergent Siphoning Tube Pressure Washer RinsingAutomatic Cool Down System Thermal ReliefMaintenance Section SpecificationsGeneral Maintenance Recommendations Pressure Washer MaintenanceMaintenance Engine MaintenanceNozzle Maintenance Ring MaintenanceStorage Preparing the Unit for StorageStoring the Engine Protecting the PumpProblem Cause Correction TroubleshootingTroubleshooting Limited Warranty Reglas de Seguridad Conserve Estas InstruccionesSección 1 Reglas de Seguridad Cuando Añada CombustibleCuando Pruebe LA Bujía DEL Motor Precaución Extensión para Boquillas con Conexión Rápida Le Características y ControlesConozca SU Maquina Lavadora DE Presion Preparando EL Lavador a Alta Presión Para SU USO MontajeMontaje Sección 3 Montaje Agregar Aceite al Motor y GasolinaConecte la Manguera y el Suministro de Agua a la Bomba Lista de Revision Previa al Arranque del MotorOperación Cómo Usar SU Máquina Lavadora a PresiónUbicación del Lavadora a Presión Cómo Darle Arranque a su Máquina Lavadora a PresiónEl Pasador de la Seguridad Sección 4 OperaciónCómo Detener su Máquina Lavadora a Presión Utilización de la Bandeja de Accesorios Cómo Usar el Sistema de Boquillas ProjectProLa Presión Baja La Presión AltaLimpieza y Aplicación del Detergentes Detergentes caseros podrían dañar la bombaEnjuage de la Máquina Lavadora a Presión Limpiando el TuboSistema de Enfriamiento Automático Alivio Térmico Para aplicar el detergente, siga los siguientes pasosMantenimiento EspecificacionesRecomendaciones Generales Mantenimiento DE LA Maquina Lavadora a PresionSección 5 Mantenimiento Mantenimiento DEL MotorMantenimiento de la Boquilla Mantenimiento de los Anillos OAlmacenamiento Preparando LA Unidad Para SU AlmacenamientoAlmacenando EL Motor Proteger la BombaDiagnosticos de Averías Reparacion DE AveriasUso del consumidor Uso comercial