Briggs & Stratton 020251 Pressure Washer Rinsing, Automatic Cool Down System, Thermal Relief

Page 13

Section 4: Operation

8.Apply detergent to a dry surface, starting at lower portion of area to be washed and work upward, using long, even, overlapping strokes.

9.Allow detergent to soak in between 3–5 minutes before washing and rinsing. Reapply as needed to prevent surface from drying. DO NOT allow detergent to dry on (prevents streaking).

Pressure Washer Rinsing

After detergent is applied, scour the surface and rinse it clean as follows:

1.Apply trigger lock to spray gun.

2.Make sure both chemical shut-off valves are in “Off” position.

3.Remove black ProjectPro™ cleaning detergent nozzle from nozzle extension.

4.Select and install desired ProjectPro™ nozzle, as described in “How to Use ProjectPro™ Nozzle System”.

5.Keep spray gun a safe distance from spray surface.

WARNING

High pressure spray could cause you to fall if you are too close to the cleaning surface.

•Keep spray nozzle between 8 to 24 inches away from cleaning surface.

•Operate this unit on a stable surface.

•Be extremely careful if you must use the pressure washer from a ladder, scaffolding or any other relatively unstable location.

•Firmly grasp spray gun with both hands when using high pressure spray to avoid injury if gun kicks back.

6.Apply a high pressure spray to a small area and then check the surface for damage. If no damage, proceed to step 7.

7.Start at top of area to be rinsed, working down with same overlapping strokes used for cleaning.

Automatic Cool Down System

(Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun, circulating water in the pump can reach temperatures above 125°F.The system engages to cool the pump by

discharging the warm water onto the ground.

13

Image 13

Contents 020251 2900 PSI Safety Rules Table of ContentsEquipment Description Operate pressure washer only outdoors When Adding FuelHigh pressure spray may damage fragile items including glass Safety Goggles not shown Always use the enclosed Features and Controls SectionKnow Your Pressure Washer Nozzle Extension with Quick Connect Allows you toCarton Contents AssemblyAttach Handle and Accessory Tray Preparing Pressure Washer for USEAttach Chemical Hose to Pump AssemblyAdd Engine Oil and Fuel Connect Hose and Water Supply to Pump Checklist Before Starting EngineConnect high pressure hose here Not use ifOperation Section HOW to USE Pressure WasherPressure Washer Location To Start Your Pressure WasherHow to Use Accessory Tray How to Stop Your Pressure WasherEngage trigger lock on spray gun when not in use OperationFollow these instructions to change ProjectPro nozzles How to Use ProjectPro Nozzle SystemEngage trigger lock on spray gun To apply detergent follow these steps Cleaning and Applying DetergentOn Position Off Position Automatic Cool Down System Pressure Washer RinsingThermal Relief If you run the engine on your pressure washer forSpecifications Section MaintenanceGeneral Maintenance Recommendations Pressure Washer MaintenanceNozzle Maintenance MaintenanceRing Maintenance Use wire herePump Maintenance Engine MaintenanceChanging Pump Oil Change pump oil as followsPreparing Unit for Storage StorageStoring the Engine Protecting the PumpTroubleshooting TroubleshootingProblem Cause Correction Years or Consumer Use YearsCommercial Use DaysConserve Estas Instrucciones Tabla DE Contenidos Reglas de SeguridadDescripción DEL Equipo Instrucciones DE SeguridadCuando Añada Combustible Sección 1 Reglas de SeguridadPrecaución Conozca SU Maquina Lavadora DE Presion Características y ControlesMontaje MontajePreparando EL Lavador a Presión Para SU USO Montaje de Manguera de Productos Químicos a Bomba Sección 3 MontajeAgregar Aceite al Motor y Gasolina Coloque la lavadora a presión sobre una superficie niveladaLista de Revision Previa al Arranque del Motor Conecte la Manguera y el Suministro de Agua a la BombaDeposite la gasolina adecuada en el tanque del combustible Proporcione el suministro de agua adecuadoCómo Usar SU Lavadora a Presión OperaciónUbicación del Lavadora a Presión Cómo Darle Arranque a su Lavadora a PresiónCómo Detener su Máquina Lavadora a Presión Sección 4 OperaciónUtilización de la Bandeja de Accesorios La Presión Baja Cómo Usar el Sistema de Boquillas ProjectProLa Presión Alta Coloque el pestillo de seguridad de la pistola de rociadoOn Posición Off Posición Limpieza y Aplicación del QuímicoDetergentes caseros podrían dañar la bomba Sistema de Enfriamiento Automático Alivio Térmico Enjuage de la Máquina Lavadora a PresiónColoque el cerrojo de seguridad a la pistola de rociado Especificaciones MantenimientoRecomendaciones Generales Antes de Cada UsoMantenimiento de la Boquilla Sección 5 MantenimientoMantenimiento de los Anillos O Mantenimiento de la BombaMantenimiento DEL Motor Sección 5 y 6 Mantenimiento y AlmacenamientoPreparando LA Unidad Para SU Almacenamiento Almacenando EL MotorReparacion DE Daños Diagnosticos de AveríasGarantía Limitada