Zenoah EXZ2500S-BC, EX-BC, EX-LRT, EX-PS, EX-HE Fueling the Unit, For Your Engine LIFE, Avoid

Page 20

7. Fuel

again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to abnormally lean mixture.

5.Put a clear indication on the outside of the container to avoid mixing up with gasoline or other containers.

6.Indicate the contents on outside of container for easy identification.

FUELING THE UNIT

1.Untwist and remove the fuel cap. Rest the cap on a dustless place.

2.Put fuel into the fuel tank to 80% of the full capacity.

3.Fasten the fuel cap securely and wipe up any fuel spillage around the unit.

WARNING

1.Select bare ground for fueling.

2.Move at least 10feet (3meters) away from the fueling point before starting the engine.

3.Stop the engine before refueling the unit. At that time, be sure to sufficiently agitate the mixed gasoline in the container.

FOR YOUR ENGINE LIFE, AVOID;

1.FUEL WITH NO OIL(RAW GASOLINE) – It will cause severe damage to the internal engine parts very quickly.

2.GASOHOL – It can cause deterioration of rubber and/or plastic parts and disruption of engine lubrication.

3.OIL FOR 4-CYCLE ENGINE USE – It can cause spark plug fouling, exhaust port blocking, or piston ring sticking.

4.Mixed fuels which have been left unused for a period of one month or more may clog the carburetor and result in the engine failing to operate properly.

5.In the case of storing the product for a

20

long period of time, clean the fuel tank after rendering it empty. Next, activate the engine and empty the carburetor of the composite fuel.

6.In the case of scrapping the used mixed oil container, scrap it only at an authorized repository site.

NOTE

As lot details of quality assurance, read the description in the section Limited Warranty carefully. Moreover, normal wear and change in product with no functional influence are not covered by the warranty. Also, be careful that, if the usage in the instruction manual is not observed as to the mixed gasoline, etc. described therein, it may not be covered by the warranty.

Image 20
Contents OWNER/OPERATOR Manual 848-BP6-93A1Safety First ContentsParts location  3 Specifications  4  5  Symbols on the machine  6 For safe operation Working ConditionWorking Circumstance  7 Working Plan  8  9  Before Starting the EngineStarting the Engine Using the Product  10 Maintenance If Someone ComesHandling Fuel  11 Transportation  12 Set up  13 EX-BC SE1 SE2 Installing Debris Guard Installing Cutting Head SE2Debris guard Plate Screw EX-BC SE3 Balance Unit 15  EX-LRT SE1 Attaching the Trimming Mechanism SE1Main pipe Trimming mechanism Screw hole Fastening bolt EX-PS SE1 Attaching the Pruning Mechanism SE1 EX-PS SE2EX-PS SE3  16 Chain tension adjusting screw Loosen Tighten EX-PS SE4 EX-PS SE5 EX-PS SE6Hole Moving direction Chain tensioner nut  17 EX-HE SE1 EX-HE SE2 EX-HE SE3 EX-HE SE4 Clamp bolt Lock screwBracket  18 HOW to MIX Fuel FuelRecommended Mixing Ratio Gasoline 50OIL  19  20  Fueling the UnitFor Your Engine LIFE, Avoid Operation  21  22  OP6 OP7 OP8Stopping Engine OP6 Adjusting Throttle Cable Adjusting Idling Speed OP10OP9  23 Operation EX-BC only  24  25  EX-BC OP4 EX-BC OP5 EX-BC OP6 Bracket HandleCutting Method  26 EX-BC OP7 EX-BC OP8 Operation Controlling Blade BounceWhat causes kick out  27  28  How you can reduce the chance of kick outHow you can maintain the best control  29  EX-BC OP9 Maintenance BladeTransporting the Unit Adjusting the Angle of the Cutting Blades OP1 Operation EX-LRT onlyEX-LRT OP1 Clamp lever Trimming mechanismAdjusting OIL Flow Rate Operation EX-PS onlyEX-PS OP1 EX-PS OP2 Checking OIL Supply  31  32   33  Operation EX-HE onlyEX-HE OP1  34  MaintenanceMaintenance Chart  35  MA4  36 Muffler Spark ArresterProcedures to be Performed After Every 100 Hours of USE MA51MA6 Cylinder Intake air cooling vent backMaintenance EX-BC only For safety reasons, do not use metalreinforced lineGear Case MA5  38 EX-LRT MA1 EX-LRT MA2 Blades MA1 Upper blade Lower bladeQuick TIP Gear CaseMaintenance EX-PS only EX-PS MA1 MA2 MA3 Oiling PortGuide BAR  40 SAW Chain EX-PS MA4 MA5 MA6Sprocket EX-PS MA7 MA8 MA9  42  43  Maintenance EX-HE onlyMA1 Gear Case Troubleshooting guide StorageCheck Probable Causes Action  44 Parts list EX-LRT ATT EX-PS ATT EX-HE ATTEXZ-PU S/N 302845 and up  46  47  EX-BC S/N 302960 and up  48  49  Engine Unit 50100000 and up  50  51  Description Part Number QtyEX-LRT S/N 000531 and up  52  53  Casing BEX-PS S/N 000000 and up  54  55  EX-HE S/N 000101 and up  56  57  Limited Warranty RedMax Garantie limitée Komatsu Zenoah America INC