Zenoah EXZ2600DL, EXZ2500S-BC, EX-BC, EX-LRT, EX-PS, EX-HE manual Transportation,  12 

Page 12

5. For safe operation

refill the tank of the unit in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel.

2.Never smoke while operating the unit or refilling its fuel tank.

3.When refilling the tank, always turn off the engine and allow it to cool down. Take a careful look around to make sure that there are no sparks or open flames anywhere nearby before refueling.

4.Wipe spilled fuel completely using a dry rag if any fuel spillage occurs during refueling.

5.After refueling, screw the fuel cap back tightly onto the fuel tank and then carry the unit to a spot 10 feet or more away from where it was refueled before turning on the engine.

TRANSPORTATION

1.When hand-carrying the product, cover over the cutting part if necessary, lift up the product and carry it paying attention to the blade.

2.Never transport the product over rough roads over long distances by vehicle without removing all fuel from the fuel tank. If doing so, fuel might leak from the tank during transport.

12

Image 12
Contents OWNER/OPERATOR Manual 848-BP6-93A1Safety First ContentsParts location  3 Specifications  4  5  Symbols on the machine  6 For safe operation Working ConditionWorking Circumstance  7 Working Plan  8 Before Starting the Engine Starting the Engine 9  Using the Product  10 Maintenance If Someone ComesHandling Fuel  11 Transportation  12 Set up  13 EX-BC SE1 SE2 Installing Debris Guard Installing Cutting Head SE2Debris guard Plate Screw EX-BC SE3 Balance UnitEX-LRT SE1 Attaching the Trimming Mechanism SE1 Main pipe Trimming mechanism Screw hole Fastening bolt 15  EX-PS SE1 Attaching the Pruning Mechanism SE1 EX-PS SE2EX-PS SE3  16 Chain tension adjusting screw Loosen Tighten EX-PS SE4 EX-PS SE5 EX-PS SE6Hole Moving direction Chain tensioner nut  17 EX-HE SE1 EX-HE SE2 EX-HE SE3 EX-HE SE4 Clamp bolt Lock screwBracket  18 HOW to MIX Fuel FuelRecommended Mixing Ratio Gasoline 50OIL  19 Fueling the Unit For Your Engine LIFE, Avoid 20  Operation  21 OP6 OP7 OP8 Stopping Engine OP6 22  Adjusting Throttle Cable Adjusting Idling Speed OP10OP9  23 Operation EX-BC only  24  25  EX-BC OP4 EX-BC OP5 EX-BC OP6 Bracket HandleCutting Method  26 EX-BC OP7 EX-BC OP8 Operation Controlling Blade BounceWhat causes kick out  27 How you can reduce the chance of kick out How you can maintain the best control 28  EX-BC OP9 Maintenance Blade Transporting the Unit 29  Adjusting the Angle of the Cutting Blades OP1 Operation EX-LRT onlyEX-LRT OP1 Clamp lever Trimming mechanismAdjusting OIL Flow Rate Operation EX-PS onlyEX-PS OP1 EX-PS OP2 Checking OIL Supply  31  32  Operation EX-HE only EX-HE OP1 33  Maintenance Maintenance Chart 34   35  MA4  36 Muffler Spark ArresterProcedures to be Performed After Every 100 Hours of USE MA51MA6 Cylinder Intake air cooling vent backMaintenance EX-BC only For safety reasons, do not use metalreinforced lineGear Case MA5  38 EX-LRT MA1 EX-LRT MA2 Blades MA1 Upper blade Lower bladeQuick TIP Gear CaseMaintenance EX-PS only EX-PS MA1 MA2 MA3 Oiling PortGuide BAR  40 EX-PS MA4 MA5 MA6 SprocketSAW Chain EX-PS MA7 MA8 MA9  42 Maintenance EX-HE only MA1 Gear Case 43  Troubleshooting guide StorageCheck Probable Causes Action  44 Parts list EX-LRT ATT EX-PS ATT EX-HE ATTEXZ-PU S/N 302845 and up  46  47  EX-BC S/N 302960 and up  48  49  Engine Unit 50100000 and up  50  51  Description Part Number QtyEX-LRT S/N 000531 and up  52  53  Casing BEX-PS S/N 000000 and up  54  55  EX-HE S/N 000101 and up  56  57  Limited Warranty RedMax Garantie limitée Komatsu Zenoah America INC