Worksaver SDM40-72, SDM40-48, SDM40-60 manual Block Cutter in Position, Checked

Page 19

INSTRUCTIONS (continued)

In some cases it will be necessary to shorten the PTO assembly to match your particular tractor. The following procedure should be used:

1.Raise the tractor 3-pt. hitch so the input shaft of the cutter gearbox is in line with the PTO shaft on the trac- tor. Shut down tractor, leaving cutter in position of shortest distance between shafts. SECURELY

BLOCK CUTTER IN POSITION.

2.Pull driveline apart. Attach outer (female) section to tractor PTO shaft. Pull on driveline section to be sure that yoke locks into place.

3.Hold driveline sections parallel to each other to determine if too long. Each section should end approximately 3” (76mm) short of reaching universal joint shield on opposite section. If too long, measure 3” (76mm) back from universal joint shield and mark on opposite section (Figure 3). Do this for both sec- tions. DO NOT CUT UNTIL STEPS 4 AND 5 ARE

CHECKED.

Figure 2.

NOTE: The use of a PTO over-running clutch or exten- sion could require that the PTO driveline be shortened a considerable amount. If this is done, the driveline halves may separate when the cutter is lowered to the ground or when operated on rough ground.

An optional special driveline that is equipped with an over- running clutch is recommended (see optional equipment).

1.Raise and lower the cutter to determine position with greatest distance between the PTO shaft and gearbox input shaft. Shut tractor off, leaving cutter in position of greatest distance between shafts. SECURELY

BLOCK CUTTER IN POSITION.

2.Hold driveline sections parallel to each other and check for minimum 6” (15cm) overlap. If driveline has been marked for cutting, overlap will be the distance between the two marks. If driveline has less than minimum overlap, do not use. Contact authorized dealer.

Figure 3.

3.If driveline must be cut to a shorter length, clamp driveline in a well padded vise to prevent damage to the shield. Cut off shield where marked. Using cut-off section of shield as a guide, cut shaft the same amount. (Figure 4.)

4.Repeat the procedure to the other driveline half. Remove all burrs and cuttings.

5.Apply multi-purpose grease to inside of outer (female) driveline section. Assemble driveline and install on tractor and cutter. Pull on each driveline section to be sure yokes lock into place. Make certain driveline shielding is in place and in good condition.

Figure 4.

W ARNING!

When attaching PTO yoke to tractor PTO shaft, it is important that spring-activated locking pin or balls operate freely and are seated in groove on PTO shaft. A loose shaft could slip off and result in personal injury or damage to equipment.

6.Carefully raise and lower the cutter and check to be sure the PTO assembly does not jam. If it does, cut equal amounts from each half of the PTO assembly.

18

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Standard Duty 3-PT. Mounted Rotary Cutter To the Owner Table of ContentsSubject Model SDM40-48 Model SDM40-60 Model SDM40-72 Cutter SpecificationsE C K L I S T S Delivery Checklist Daily ChecklistThis Symbol Means Become Alert Your Safety is Involved P O Rtant Safety InformationBefore YOU Start DON’T TRY IT Equipment Safety GuidelinesTire Safety Safety SignsSafety Training Preparation Operational Safety Starting and Stopping SafetyOperational Safety Safety Instructions Transport Safety Maintenance Safety Storage Safety Maintenance SafetySafety Sign Locations Safety Sign LocationsRPM Speed Range only For Agricultural USE only Tractor Requirements and Prepa R AtionChecked Block Cutter in PositionAT TA C H M E N T PTO Driveline Insta L L AtionConnect the PTO Driveline AT this Time Adjusting for Work Gearbox OIL Fill General SafetyPRE Operation Checklist Uneven Terrain E R Ating TechniqueE R Ating Tips ShreddingOptions A D E SA N S P O Rting Removing Cutter from T R a C T O RAT the END of Your Cutting Season Routine MaintenanceB R I C Ation Information Daily ChecksBlade Servicing Shear Bolt ReplacementBlade Sharpening Blade Beam & Gearbox Insta L L Ation Pair of Optional Chain ShieldingBlade Beam & Gearbox R E M O VA L Proper Torque for FA S T E N E R S Leaves a streak of uncut or partially cut grass Troubleshooting GuideMaterial discharges from Cutter seems to require Excessive wear Disclaimer of Implied Warranties & Consequential Damages This Warranty Shall not ApplyWorksaver Description Reqd PTO Shaft Shear Bolt Protected PA RTS View & PA RTS ListPart Description Reqd SDM40-60 PA RTS View SDM40-48 4’ Cutter PA RTS ListSDM40-72 6’ Cutter PA RTS List SDM40-60 5’ Cutter PA RTS ListComer Gearbox LF-135.802 PA RTS View ’ Cutter Worksaver Comer Description Reqd Comer Gearbox LF PA RTS List ’ CutterComer Gearbox PA RTS View Comer Gearbox LF PA RTS List Make Every DAY Holiday from Accidents

SDM40-60, SDM40-48, SDM40-72 specifications

The Worksaver SDM series, including models SDM40-72, SDM40-48, and SDM40-60, represents a significant advancement in material handling technology designed for agricultural and landscaping applications. These robust and versatile skid-steer and tractor attachments provide users with an efficient solution for a variety of tasks, including moving and grading soil, gravel, and other materials.

The SDM40-72 model boasts a 72-inch wide blade, while the SDM40-48 and SDM40-60 come with 48-inch and 60-inch blades, respectively. This range in size allows users to choose the perfect model to fit their specific needs and the dimensions of their equipment. The heavy-duty construction of the blades ensures durability and toughness, capable of withstanding rigorous use in demanding environments.

One of the standout features of the Worksaver SDM series is the intelligent design of the blade itself. The blades are equipped with a quick-attach system, making it easy for operators to switch attachments quickly, enhancing productivity on the job site. This feature is particularly valuable for contractors who may need to adapt to varying application requirements throughout the day.

The SDM series also incorporates innovative tilt and angle adjustment mechanisms. This allows operators to fine-tune the blade position for precise material handling and grading. With adjustable tilt angles, users can achieve optimal results whether they are leveling surfaces, backfilling, or creating drainage ditches.

Additionally, the Worksaver SDM models are designed to integrate seamlessly with a variety of skid-steers and tractors, ensuring versatility across different machinery brands. The universal mounting plate allows for quick attachment to most popular equipment models, eliminating compatibility issues that can slow down operations.

Safety is prioritized in the design of the SDM series, which includes reinforced edges and a robust framework. This ensures not only the safety of the operator but also the longevity of the attachment. The blades are constructed from high-quality materials designed to resist wear and enhance performance over time.

In summary, the Worksaver SDM40-72, SDM40-48, and SDM40-60 models are exceptional choices for professionals seeking reliable and efficient material handling solutions. Their innovative features, durable construction, and compatibility with various equipment make them ideal for tackling a wide range of tasks in agricultural and landscaping applications. Users can expect enhanced efficiency and productivity with these outstanding attachments.
Top Page Image Contents