Worksaver SDM40-72, SDM40-48, SDM40-60 manual Excessive wear

Page 31

 

TROUBLESHOOTING

GUIDE

P R O B L E M

POSSIBLE CAUSE

POSSIBLE REMEDY

 

 

 

 

 

 

Gearbox noisy.

1. Rough gears.

Run in or change gears.

 

2. Worn bearings.

Replace bearing.

 

3.

Low oil in gearbox.

Check level and add oil.

 

4.

Improper gearbox lubricant.

Replace with proper lubricant.

 

 

 

 

 

 

 

 

Gearbox leaking.

1.

Damaged oil seal.

Replace seal.

 

2.

Bent shaft.

Replace oil seal and shaft.

 

3.

Shaft rough in oil seal area.

Replace or repair shaft.

 

4.

Oil seal installed wrong.

Replace seal.

 

5.

Oil seal not sealing in the

Replace seal or use a sealant

 

 

housing.

on outside diameter of seal.

 

6.

Oil level too high.

Drain oil to proper level.

 

7.

Hole in gearbox.

Replace gearbox.

 

8.

Gasket damaged.

Replace gasket.

 

9.

Bolts loose.

Tighten bolts.

 

 

 

 

 

 

 

 

 

 

 

 

Excessive wear of

1.

Tire not turning properly.

Check wheel assembly for proper

tailwheel tire.

 

 

lubrication. Axle bolt could be too

 

 

 

tight.

 

2.

Tailwheel not castering properly.

Check tailwheel yoke assembly for

 

 

 

proper lubrication or for mechanical

 

 

 

binding.

 

 

 

 

 

 

 

 

Front hitch “A” frame

1.

Operator turning sharply hitting

bending sideways.

 

objects with tailwheel frame or

 

 

cutter deck.

 

2.

Tailwheel not castering properly.

 

3.

Cutter is being operated to low

 

 

and cutter deck is contacting

 

 

ground during turns.

 

4.

Tractor 3 pt. hitch is leaking down

 

 

and cutter deck is contacting

 

 

ground.

Drive carefully and plan turns to avoid hitting buildings, posts, trees, etc.

Check tailwheel yoke (see above under tire wear).

A. Raise cutter (especially on rough ground).

B. Set stop on hitch controls lever so hitch lift arms do not drop cutter on ground.

A. Repair tractor hitch hydraulic system. B. Use limit chains to keep lift arms from going lower than set limit.

30

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Standard Duty 3-PT. Mounted Rotary Cutter To the Owner Table of ContentsSubject Model SDM40-48 Model SDM40-60 Model SDM40-72 Cutter SpecificationsE C K L I S T S Delivery Checklist Daily ChecklistThis Symbol Means Become Alert Your Safety is Involved P O Rtant Safety InformationBefore YOU Start DON’T TRY IT Equipment Safety GuidelinesTire Safety Safety SignsSafety Training Preparation Operational Safety Starting and Stopping SafetyOperational Safety Safety Instructions Transport Safety Maintenance Safety Storage Safety Maintenance SafetySafety Sign Locations Safety Sign LocationsRPM Speed Range only For Agricultural USE only Tractor Requirements and Prepa R AtionChecked Block Cutter in PositionAT TA C H M E N T PTO Driveline Insta L L AtionConnect the PTO Driveline AT this Time Adjusting for Work Gearbox OIL Fill General SafetyPRE Operation Checklist Uneven Terrain E R Ating TechniqueE R Ating Tips ShreddingOptions A D E SA N S P O Rting Removing Cutter from T R a C T O RAT the END of Your Cutting Season Routine MaintenanceB R I C Ation Information Daily ChecksBlade Servicing Shear Bolt ReplacementBlade Sharpening Blade Beam & Gearbox Insta L L Ation Pair of Optional Chain ShieldingBlade Beam & Gearbox R E M O VA L Proper Torque for FA S T E N E R S Leaves a streak of uncut or partially cut grass Troubleshooting GuideMaterial discharges from Cutter seems to require Excessive wear Disclaimer of Implied Warranties & Consequential Damages This Warranty Shall not ApplyWorksaver Description Reqd PTO Shaft Shear Bolt Protected PA RTS View & PA RTS ListPart Description Reqd SDM40-60 PA RTS View SDM40-48 4’ Cutter PA RTS ListSDM40-72 6’ Cutter PA RTS List SDM40-60 5’ Cutter PA RTS ListComer Gearbox LF-135.802 PA RTS View ’ Cutter Worksaver Comer Description Reqd Comer Gearbox LF PA RTS List ’ CutterComer Gearbox PA RTS View Comer Gearbox LF PA RTS List Make Every DAY Holiday from Accidents

SDM40-60, SDM40-48, SDM40-72 specifications

The Worksaver SDM series, including models SDM40-72, SDM40-48, and SDM40-60, represents a significant advancement in material handling technology designed for agricultural and landscaping applications. These robust and versatile skid-steer and tractor attachments provide users with an efficient solution for a variety of tasks, including moving and grading soil, gravel, and other materials.

The SDM40-72 model boasts a 72-inch wide blade, while the SDM40-48 and SDM40-60 come with 48-inch and 60-inch blades, respectively. This range in size allows users to choose the perfect model to fit their specific needs and the dimensions of their equipment. The heavy-duty construction of the blades ensures durability and toughness, capable of withstanding rigorous use in demanding environments.

One of the standout features of the Worksaver SDM series is the intelligent design of the blade itself. The blades are equipped with a quick-attach system, making it easy for operators to switch attachments quickly, enhancing productivity on the job site. This feature is particularly valuable for contractors who may need to adapt to varying application requirements throughout the day.

The SDM series also incorporates innovative tilt and angle adjustment mechanisms. This allows operators to fine-tune the blade position for precise material handling and grading. With adjustable tilt angles, users can achieve optimal results whether they are leveling surfaces, backfilling, or creating drainage ditches.

Additionally, the Worksaver SDM models are designed to integrate seamlessly with a variety of skid-steers and tractors, ensuring versatility across different machinery brands. The universal mounting plate allows for quick attachment to most popular equipment models, eliminating compatibility issues that can slow down operations.

Safety is prioritized in the design of the SDM series, which includes reinforced edges and a robust framework. This ensures not only the safety of the operator but also the longevity of the attachment. The blades are constructed from high-quality materials designed to resist wear and enhance performance over time.

In summary, the Worksaver SDM40-72, SDM40-48, and SDM40-60 models are exceptional choices for professionals seeking reliable and efficient material handling solutions. Their innovative features, durable construction, and compatibility with various equipment make them ideal for tackling a wide range of tasks in agricultural and landscaping applications. Users can expect enhanced efficiency and productivity with these outstanding attachments.
Top Page Image Contents