Worksaver EM/2 60, EM/2 72 warranty S E M B LY Instructions

Page 20

A S S E M B LY INSTRUCTIONS

The mower will attach to most tractors with a Category I, 3 pt. hitch system and a 540 RPM PTO. Do not exceed horsepower recommendations.

D A N G E R !

Operating with PTO speed over 540 RPM can cause excessive vibration and mower failure, which can result in serious injury or even death.

DEALER SET-UP INSTRUCTIONS

Assembly of this mower is the responsibility of the dealer. The mower should be delivered to the owner completely assembled, lubricated and adjusted for normal cutting conditions.

Set-up mower as received from the factory with these instructions.

•Remove mower from crate.

•Complete assembly of factory pre-assembled hitch.

•Refer to parts lists and exploded view drawings for more details.

•To complete assembly, it will be easier if components are aligned and assembled loosely before tightening hardware.

CAUTION!

Always use personal protection devices such as eye and ear protection during assembly.

A-FRAME AT TA C H M E N T

Attach the rear brace bars (1) to the lugs on the rear of the deck with M12 bolt, washer, lockwasher, and locknut. Attach the A-Frame bars (2) to the lugs on the front of the deck with M12 bolt, washer, lockwasher, and locknut. Attach the other end of the A-Frame bars (2) at the top and between the rear brace bars and top link (3) with M12 bolt, (2 each) washer, (3 each) spacer, lockwasher, and locknut. See figure 1.

Figure 1

3 PT. HITCH AT TA C H M E N T

Remove bolt from hitch point location and assemble as shown in figure 2.

Figure 2

CASTER WHEEL AT TA C H M E N T

Some mowers will be supplied with all four wheels fully assembled. However, for models that do require assembly, please follow these instructions. Install two 3/4” spacers on each fork and wheel assembly shaft. Insert fork shaft into axle arm weldment. Additionally install two 3/4” and two 3/8” spacers on each axle shaft and retain using the snapper pins supplied. See figure 3.

Figure 3

DRIVELINE

TO MOWER

GEARBOX

AT TA C H M E N T

1.Grab and turn the yoke collar of the driveline end to be attached to the gearbox. Note: Make sure that you connect the driveline end with the male shield tube to the mower.

2.Slide the yoke with the collar turned onto the mower’s gearbox input shaft. Note: Make sure that the plas- tic protective cone is mounted on the gearbox.

3.Move yoke back and forth until its locking pin has engaged on the gearbox input shaft groove.

19

Page 19 Page 21
Image 20
Page 19 Page 21
Contents PT. Rear Finishing Mower Retail CUSTOMER’S Responsibility Delivery Checklist PRE Operation ChecklistTo the Owner/Operator/Dealer Before YOU StartSafety Instructions Equipment Safety GuidelinesSafety Signs Tire SafetySafety Training Preparation Starting and Stopping Safety Operational SafetyOperational Safety Safety Instructions Transport Safety Maintenance Safety Maintenance Safety Storage SafetySafety Sign Location Replace Safety Signs if Damaged or Missing To prevent serious injury or death N G E R S T R U C T I O N S Tractor Requirements and Prepa R AtionS E M B LY Instructions Tractor Prepa R Ation Cutting Height AdjustmentE R Ation Instructions Cutting Speed Cutting TipsTaching and Storing Before OperatingDriveline Length Check P R O C E D U R E Adjusting Driveline LengthFront Gauge Wheel Interference Check Troubleshooting StreakingTroubleshooting Maintenance Instructions B R I C AT I O NGearbox Lubrication Gauge Wheel AssembliesDriveline Lubrication Blade Spindle LubricationBlade Servicing Blade SharpeningDrive Belt Adjustment Drive Belt R E M O VAL and Insta L L AtionBlade Spindle Service Instructions Assembly O R a G ELW AY S Obey ALL Safety Rules LW AYS be Careful Replacement PA RT S Table of ContentsN E R a L M O W E R a S S E M B LY PA RTS Draw I N G PA RTS List A R B O PA RTS Draw I N G A R B O PA RTS List PA RTS Draw I N G PA RTS List Page Page Page Safety Precautions PT. Rear Finishing Mower

EM/2 60, EM/2 72 specifications

The Worksaver EM/2 series, specifically the EM/2 60 and EM/2 72 models, offers innovative solutions for a range of agricultural and landscaping tasks. Designed for efficiency, durability, and versatility, these implements are engineered to meet the demands of modern farming and yard management.

One of the standout features of the Worksaver EM/2 models is their robust construction. Built with high-quality materials, the EM/2 60 and EM/2 72 ensure longevity and resistance to wear from heavy use. The heavy-duty framework and reinforced components provide not only strength but also stability during operation, making these attachments suitable for various ground conditions.

A critical aspect of the EM/2 series is their advanced design, which allows for easy attachment to a variety of tractors and machinery. The quick-attach implement system streamlines the process of connecting and disconnecting the equipment, saving users valuable time and effort during their daily operations. This user-friendly design minimizes downtime and maximizes productivity.

In terms of functionality, both models come equipped with adjustable working widths, enabling users to customize their approach based on field size and job requirements. The EM/2 60 offers a width of 60 inches, while the EM/2 72 features a 72-inch width, allowing for flexibility whether it's grading, land leveling, or vegetation management.

The technology behind the Worksaver EM/2 series also places a strong emphasis on ease of operation. The angled blade design facilitates more efficient soil movement and material distribution, achieving better results with less effort. Additionally, the implement's ability to adapt to different terrains contributes to its effectiveness in various applications, from farmfields to residential landscaping projects.

Safety is paramount with the EM/2 models, featuring built-in safety mechanisms that ensure secure operation. The design not only protects the user but also enhances the overall operational stability of the implement, allowing for safe and effective use even in challenging environments.

Overall, the Worksaver EM/2 60 and EM/2 72 represent a significant advancement in implement technology, combining strength, user-friendliness, and adaptability. These models are ideal for farmers, landscapers, and land management professionals looking for reliable equipment that can tackle a wide range of tasks efficiently and safely, making them valuable additions to any agricultural operation.
Top Page Image Contents