Worksaver EM/2 60, EM/2 72 warranty Delivery Checklist, PRE Operation Checklist

Page 3

C H E C K L I S T S

DELIVERY CHECKLIST

Inspect the mower thoroughly after assembly to be cer- tain it is set up properly. The following checklist is a reminder of points to inspect. Check off each item as it is found satisfactory or after proper adjustment is made.

hCheck operator's manual and familiarize the opera- tor with all sections of it.

hCheck that all safety shielding is in place.

hCheck all bolts to be sure they are tight or adjusted properly at hinged locations.

hCheck that all cotter pins are properly installed.

hCheck PTO driveline. Make sure it is the correct length to operate mower with intended tractor.

hCheck that all lubrication points with grease fittings have been lubricated.

hCheck that blades have been properly installed. Check all blade bolts.

hCheck mower attitude, after mounting on tractor.

hCheck that gearbox is properly serviced and seals are not leaking.

hCheck shear bolt for proper grade and installation.

hAll safety signs (decals) in place and readable.

hWhen the cutter is transported on a road or highway at night or during the day, safety devices should be used for adequate warning to operators of other vehicles.

PRE - OPERATION CHECKLIST

(OWNER/OPERATOR RESPONSIBILITY)

____ Review and follow safety rules and safety signs on

pages 3 through 17.

____ Check that mower is properly and securely

attached to tractor.

____ Make sure driveline spring-activated locking pin or

locking balls operate freely and are seated firmly in tractor PTO spline groove.

____ Lubricate all grease fitting locations. Make sure

PTO shaft slip joint is lubricated.

____ Check to be sure gear lube runs out the small

check plug on side of gearbox.

____ Check that all hardware is properly installed.

____ Check to ensure blades are sharp and secure and

cutting edge is positioned to lead in a counter- clockwise rotation.

____ Check that all shields and guards are properly

installed and in good condition.

____ Check cutting height, front to rear attitude and top

link adjustment.

____ Place tractor PTO and transmission in neutral

before starting engine.

____ Set tractor PTO gear select lever for 540 rpm

operation.

____ Inspect area to be cut and remove stones,

branches or other hard objects that might be thrown, causing injury or damage.

____ Check that PTO driveline shields are securely

locked and clears the front of the mower frame.

I M P O RTANT!

Gearbox was not filled at factory. It must be serviced before operating. Fill to proper level with SAE 90 oil. Failure to service will result in damage to gearbox.

2

Page 2 Page 4
Image 3
Page 2 Page 4
Contents PT. Rear Finishing Mower Retail CUSTOMER’S Responsibility PRE Operation Checklist Delivery ChecklistBefore YOU Start To the Owner/Operator/DealerEquipment Safety Guidelines Safety InstructionsTire Safety Safety SignsSafety Training Preparation Operational Safety Starting and Stopping SafetyOperational Safety Safety Instructions Transport Safety Maintenance Safety Storage Safety Maintenance SafetySafety Sign Location Replace Safety Signs if Damaged or Missing To prevent serious injury or death N G E R Tractor Requirements and Prepa R Ation S T R U C T I O N SS E M B LY Instructions Cutting Height Adjustment E R Ation InstructionsTractor Prepa R Ation Before Operating Cutting SpeedCutting Tips Taching and StoringAdjusting Driveline Length Front Gauge Wheel Interference CheckDriveline Length Check P R O C E D U R E Streaking TroubleshootingTroubleshooting Gauge Wheel Assemblies Maintenance InstructionsB R I C AT I O N Gearbox LubricationBlade Sharpening Driveline LubricationBlade Spindle Lubrication Blade ServicingDrive Belt R E M O VAL and Insta L L Ation Drive Belt AdjustmentO R a G E Blade Spindle Service Instructions AssemblyLW AY S Obey ALL Safety Rules LW AYS be Careful Table of Contents Replacement PA RT SN E R a L M O W E R a S S E M B LY PA RTS Draw I N G PA RTS List A R B O PA RTS Draw I N G A R B O PA RTS List PA RTS Draw I N G PA RTS List Page Page Page PT. Rear Finishing Mower Safety Precautions

EM/2 60, EM/2 72 specifications

The Worksaver EM/2 series, specifically the EM/2 60 and EM/2 72 models, offers innovative solutions for a range of agricultural and landscaping tasks. Designed for efficiency, durability, and versatility, these implements are engineered to meet the demands of modern farming and yard management.

One of the standout features of the Worksaver EM/2 models is their robust construction. Built with high-quality materials, the EM/2 60 and EM/2 72 ensure longevity and resistance to wear from heavy use. The heavy-duty framework and reinforced components provide not only strength but also stability during operation, making these attachments suitable for various ground conditions.

A critical aspect of the EM/2 series is their advanced design, which allows for easy attachment to a variety of tractors and machinery. The quick-attach implement system streamlines the process of connecting and disconnecting the equipment, saving users valuable time and effort during their daily operations. This user-friendly design minimizes downtime and maximizes productivity.

In terms of functionality, both models come equipped with adjustable working widths, enabling users to customize their approach based on field size and job requirements. The EM/2 60 offers a width of 60 inches, while the EM/2 72 features a 72-inch width, allowing for flexibility whether it's grading, land leveling, or vegetation management.

The technology behind the Worksaver EM/2 series also places a strong emphasis on ease of operation. The angled blade design facilitates more efficient soil movement and material distribution, achieving better results with less effort. Additionally, the implement's ability to adapt to different terrains contributes to its effectiveness in various applications, from farmfields to residential landscaping projects.

Safety is paramount with the EM/2 models, featuring built-in safety mechanisms that ensure secure operation. The design not only protects the user but also enhances the overall operational stability of the implement, allowing for safe and effective use even in challenging environments.

Overall, the Worksaver EM/2 60 and EM/2 72 represent a significant advancement in implement technology, combining strength, user-friendliness, and adaptability. These models are ideal for farmers, landscapers, and land management professionals looking for reliable equipment that can tackle a wide range of tasks efficiently and safely, making them valuable additions to any agricultural operation.
Top Page Image Contents