Worksaver EM/2 60, EM/2 72 Driveline Lubrication, Blade Spindle Lubrication, Blade Servicing

Page 27

MAINTENANCE INSTRUCTIONS (continued)

DRIVELINE LUBRICATION

Grease fittings are located on the cross and bearing kit assemblies of both U-joints. U-joints should be greased after every 8 hours of operation. See figure 10 for the location of the grease fittings. Do not force grease through the needle bearing cup assemblies.

BLADE SPINDLE LUBRICATION

Blade spindles must be lubricated after every 8 hours of operation. Access the lubrication fittings through the holes in the belt guards. Each spindle is supplied with a grease fitting on top, and it must be lubricated sufficiently so that a small amount of grease escapes through the bleed hole on their underside. Do not force large amounts of grease on the spindles, as it may get on the drive belts.

Figure 10

The metal telescoping drive tubes inside the plastic shield tubes must be lubricated before each use. See figure 11.

Disconnect the driveline from the tractor and pull halves apart (do not disconnect the driveline that is attached to the mower gearbox). Insert grease into drive tube and spread it evenly. Reconnect the two driveline halves together. Reconnect the driveline to the tractor PTO, raise and lower the mower several times so that the grease just applied spreads over the entire working area of the drive tubes.

BLADE SERVICING

Use only correct specified blades on your mower. They are manufactured of special heat-treated alloy steel. Substitute blades may not meet specifications and may fail in a hazardous manner, which could cause injury.

BLADE SHARPENING

To maintain a proper blade balance, always sharpen both ends of the blade equally. Follow the sharpening pattern as shown on figure 12. Do not sharpen the blades to a razor edge, but leave a 1/32” blunt edge. Never sharpen the back side of the blades.

W ARNING!

Avoid personal injury! Always support or block the mower when servicing the blades, carrier or any other component on the underside of the deck.

B L A D E R E M O VA L

Figure 11

Figure 12

W ARNING!

When attaching the driveline yoke to the tractor PTO shaft, it is important that the spring activated locking collar turns freely and that the locking pin is seated on the PTO shaft groove. A loose yoke could slip off and result in personal injury or damage to the mower.

Hold the end of the blade using heavy leather gloves and remove the left hand threaded bolt.

26

Page 26 Page 28
Image 27
Page 26 Page 28
Contents PT. Rear Finishing Mower Retail CUSTOMER’S Responsibility PRE Operation Checklist Delivery ChecklistBefore YOU Start To the Owner/Operator/DealerEquipment Safety Guidelines Safety InstructionsTire Safety Safety SignsSafety Training Preparation Operational Safety Starting and Stopping SafetyOperational Safety Safety Instructions Transport Safety Maintenance Safety Storage Safety Maintenance SafetySafety Sign Location Replace Safety Signs if Damaged or Missing To prevent serious injury or death N G E R Tractor Requirements and Prepa R Ation S T R U C T I O N SS E M B LY Instructions Cutting Height Adjustment E R Ation InstructionsTractor Prepa R Ation Before Operating Cutting SpeedCutting Tips Taching and StoringAdjusting Driveline Length Front Gauge Wheel Interference CheckDriveline Length Check P R O C E D U R E Streaking TroubleshootingTroubleshooting Gauge Wheel Assemblies Maintenance InstructionsB R I C AT I O N Gearbox LubricationBlade Sharpening Driveline LubricationBlade Spindle Lubrication Blade ServicingDrive Belt R E M O VAL and Insta L L Ation Drive Belt AdjustmentO R a G E Blade Spindle Service Instructions AssemblyLW AY S Obey ALL Safety Rules LW AYS be Careful Table of Contents Replacement PA RT SN E R a L M O W E R a S S E M B LY PA RTS Draw I N G PA RTS List A R B O PA RTS Draw I N G A R B O PA RTS List PA RTS Draw I N G PA RTS List Page Page Page PT. Rear Finishing Mower Safety Precautions

EM/2 60, EM/2 72 specifications

The Worksaver EM/2 series, specifically the EM/2 60 and EM/2 72 models, offers innovative solutions for a range of agricultural and landscaping tasks. Designed for efficiency, durability, and versatility, these implements are engineered to meet the demands of modern farming and yard management.

One of the standout features of the Worksaver EM/2 models is their robust construction. Built with high-quality materials, the EM/2 60 and EM/2 72 ensure longevity and resistance to wear from heavy use. The heavy-duty framework and reinforced components provide not only strength but also stability during operation, making these attachments suitable for various ground conditions.

A critical aspect of the EM/2 series is their advanced design, which allows for easy attachment to a variety of tractors and machinery. The quick-attach implement system streamlines the process of connecting and disconnecting the equipment, saving users valuable time and effort during their daily operations. This user-friendly design minimizes downtime and maximizes productivity.

In terms of functionality, both models come equipped with adjustable working widths, enabling users to customize their approach based on field size and job requirements. The EM/2 60 offers a width of 60 inches, while the EM/2 72 features a 72-inch width, allowing for flexibility whether it's grading, land leveling, or vegetation management.

The technology behind the Worksaver EM/2 series also places a strong emphasis on ease of operation. The angled blade design facilitates more efficient soil movement and material distribution, achieving better results with less effort. Additionally, the implement's ability to adapt to different terrains contributes to its effectiveness in various applications, from farmfields to residential landscaping projects.

Safety is paramount with the EM/2 models, featuring built-in safety mechanisms that ensure secure operation. The design not only protects the user but also enhances the overall operational stability of the implement, allowing for safe and effective use even in challenging environments.

Overall, the Worksaver EM/2 60 and EM/2 72 represent a significant advancement in implement technology, combining strength, user-friendliness, and adaptability. These models are ideal for farmers, landscapers, and land management professionals looking for reliable equipment that can tackle a wide range of tasks efficiently and safely, making them valuable additions to any agricultural operation.
Top Page Image Contents