Worksaver EM/2 60, EM/2 72 warranty O R a G E, Blade Spindle Service Instructions Assembly

Page 29

MAINTENANCE INSTRUCTIONS (continued)

S T O R A G E

Your mower represents an investment from which you should get the greatest possible benefit and use. Therefore, when the cutting season is over, the mower should be thoroughly checked and prepared for storage so that a minimum amount of work will be required to put it back into operation for the next season.

We suggest the following storage procedures:

1.Thoroughly clean the mower

2.Lubricate the mower as recommended in the mainte- nance section of this manual.

3.Tighten all bolts and pins to the recommended torque.

4.Check the mower for worn or damaged parts and replace any require so.

5.Store the mower in a clean, dry place with the deck resting on blocks.

6.Use spray touch up enamel where necessary to pre- vent rust and maintain its appearance.

BLADE SPINDLE SERVICE INSTRUCTIONS ASSEMBLY

1.Inspect all parts for damage or wear and make sure that the bearings are in good condition. Replace any parts that show wear or any damage.

2.Clean all components and make sure that they are free of dirt, grease or any other contaminants.

3.Before assembly pack the ball bearings with quality bearing grease.

4.Press a bearing into the housing on the side that has the grease overfill hole. Make sure that the bearing’s dirt seal is facing to the outside of the housing.

5.Install a flat washer (item 6), and the dust cap (item 4). Next press the spindle shaft through the already installed bearing and be certain that the bearing is seated properly.

6.Install the spacer (item 5) on the spindle shaft. Press the second bearing into the opposite side of the housing and make sure that it is properly seated, with the dirt seal facing outside.

7.Next install the flat washer (item 6) and key (item 10) on the shaft. Mount the proper sheave that corre- sponds with the spindle.

8.Install lockwasher (item 7) and nut (item 8) on the shaft and tighten to approximately 65 ft. lb. torque.

9.Align the slot in the nut with the lockwasher tab. Bend the tab into the nut so it locks in place.

10.Grease the spindle assembly through the grease fit- ting (item 9) until a small amount of grease comes out of the relief hole in the housing.

28

Page 28 Page 30
Image 29
Page 28 Page 30
Contents PT. Rear Finishing Mower Retail CUSTOMER’S Responsibility PRE Operation Checklist Delivery ChecklistBefore YOU Start To the Owner/Operator/DealerEquipment Safety Guidelines Safety InstructionsTire Safety Safety SignsSafety Training Preparation Operational Safety Starting and Stopping SafetyOperational Safety Safety Instructions Transport Safety Maintenance Safety Storage Safety Maintenance SafetySafety Sign Location Replace Safety Signs if Damaged or Missing To prevent serious injury or death N G E R Tractor Requirements and Prepa R Ation S T R U C T I O N SS E M B LY Instructions Tractor Prepa R Ation Cutting Height AdjustmentE R Ation Instructions Cutting Tips Cutting SpeedTaching and Storing Before OperatingDriveline Length Check P R O C E D U R E Adjusting Driveline LengthFront Gauge Wheel Interference Check Streaking TroubleshootingTroubleshooting B R I C AT I O N Maintenance InstructionsGearbox Lubrication Gauge Wheel AssembliesBlade Spindle Lubrication Driveline LubricationBlade Servicing Blade SharpeningDrive Belt R E M O VAL and Insta L L Ation Drive Belt AdjustmentO R a G E Blade Spindle Service Instructions AssemblyLW AY S Obey ALL Safety Rules LW AYS be Careful Table of Contents Replacement PA RT SN E R a L M O W E R a S S E M B LY PA RTS Draw I N G PA RTS List A R B O PA RTS Draw I N G A R B O PA RTS List PA RTS Draw I N G PA RTS List Page Page Page PT. Rear Finishing Mower Safety Precautions

EM/2 60, EM/2 72 specifications

The Worksaver EM/2 series, specifically the EM/2 60 and EM/2 72 models, offers innovative solutions for a range of agricultural and landscaping tasks. Designed for efficiency, durability, and versatility, these implements are engineered to meet the demands of modern farming and yard management.

One of the standout features of the Worksaver EM/2 models is their robust construction. Built with high-quality materials, the EM/2 60 and EM/2 72 ensure longevity and resistance to wear from heavy use. The heavy-duty framework and reinforced components provide not only strength but also stability during operation, making these attachments suitable for various ground conditions.

A critical aspect of the EM/2 series is their advanced design, which allows for easy attachment to a variety of tractors and machinery. The quick-attach implement system streamlines the process of connecting and disconnecting the equipment, saving users valuable time and effort during their daily operations. This user-friendly design minimizes downtime and maximizes productivity.

In terms of functionality, both models come equipped with adjustable working widths, enabling users to customize their approach based on field size and job requirements. The EM/2 60 offers a width of 60 inches, while the EM/2 72 features a 72-inch width, allowing for flexibility whether it's grading, land leveling, or vegetation management.

The technology behind the Worksaver EM/2 series also places a strong emphasis on ease of operation. The angled blade design facilitates more efficient soil movement and material distribution, achieving better results with less effort. Additionally, the implement's ability to adapt to different terrains contributes to its effectiveness in various applications, from farmfields to residential landscaping projects.

Safety is paramount with the EM/2 models, featuring built-in safety mechanisms that ensure secure operation. The design not only protects the user but also enhances the overall operational stability of the implement, allowing for safe and effective use even in challenging environments.

Overall, the Worksaver EM/2 60 and EM/2 72 represent a significant advancement in implement technology, combining strength, user-friendliness, and adaptability. These models are ideal for farmers, landscapers, and land management professionals looking for reliable equipment that can tackle a wide range of tasks efficiently and safely, making them valuable additions to any agricultural operation.
Top Page Image Contents