Simplicity UVGT1621BV, UVG1621BV, UV1621BV important safety instructions Battery Removal

Page 27

SECTION 4 – ADJUSTMENTS & REPAIRS

4.2SERVICE BRAKE & PARK BRAKE ADJUSTMENT (Continued)

8.Operate machine on smooth flat surface at approximately 1/2 speed.

9.Apply brake firmly. Machine should stop in a straight line and not pull to either the right or the left. Also both rear tires should begin to skid evenly.

10.If the machine pulls to the left or the left tire skids before the right, tighten the right brake adjustment nut 1/4 turn clockwise.

11.If the machine pulls to the right or the right tire skids before the left, tighten the left brake adjustment nut 1/4 turn clockwise.

12.Continue until the machine stops straight and both tires skid evenly.

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. STOP engine. Set park brake. Shift transmission to Neutral. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine.

4.3 BATTERY

NOTE: The battery in this machine is maintenance-free. It has been filled to the proper level with acid and is sealed. Do not attempt to open the battery.

4.3.1. Battery Removal

1.The battery is located under operator’s seat. Remove seat knobs and carefully tilt forward to expose battery. See Figure 4.3.

2.Observe and note cable positions on battery. See Figure 4.4.

3.Disconnect cables from battery terminals, disconnecting BLACK (Negative) cables first. Retain hardware.

FRONT OF MACHINE

POSITIVE (+) CABLES

 

NEGATIVE (-)

(RED) WITH TERMINAL

 

CABLES (BLACK)

COVER

 

 

 

 

 

BATTERY

RETAINING

STRAP

FIGURE 4.4

4.Remove battery retaining strap hardware and carefully lift battery out of battery tray. See Figure 4.4.

WARNING

Cables must be connected to battery terminals in the proper position as shown in Figure 4.4. DO NOT attempt to charge battery while installed on the Machine. DO NOT use “BOOST” chargers on the battery.

SEAT KNOBS

FIGURE 4.3

275

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Manual No -6153 Rev , 11/11/04 Turf Cruiser Trail CruiserProtection Against Tipovers Protection for ChildrenCarrying Loads TowingPreparation Operation Safe Handling of GasolineElectric Winch Operation Powerlinktm by Briggs & StrattonMaintenance Not featured on all modelsMaintenance Table of Contents Introduction FamiliarizationControl Console Dashboard / Pedal ClusterControl Identification & Safety Signs Headlight SwitchOperator Protective Structure Specifications & Maintenance Powerlink WarningsAvoid Serious Injury or Death PRE-START Check List Operating InstructionsControls Function and Operation Check Safety Interlocks for proper functionFrom previous Powerlink Generator System not on all Speedometer/Fuel Gauge ComboWarn Electric Winch not on all models Starting and Stopping Machine Motion Starting and Stopping EngineUsing Differential Lock Parking MachineDriving the Machine General Operating Procedures Carrying LoadsTowing Water Crossing Transporting MachineStarting the Powerlinktm Generator Testing the GfciStopping the Powerlinktm Generator Introduction MaintenanceService After First 5 Hours Service Engine Air CleanerCheck Wheel Lug Nuts Lubrication -Axle Couplings & Steering PinsCheck Transmission Fluid Level Check Tire PressureService Every 50 Operating Hours Service Every 25 Operating HoursService Every 100 Operating Hours Service Every 200 Operating Hours Or YearlyStorage OUT of Season Adjustments & Repairs Service Brake & Park Brake AdjustmentDrive Belt Replacement Battery Removal BatteryState of Charge Digital Voltmeter Cargo BED Latch Striker AdjustmentBattery Installation Battery TestingTransmission Shift ROD Adjustment Electrical 3128 Troubleshooting To be Performed Pages Maintenance ScheduleYear Limited Warranty Product Registration Form Utility Vehicles Series
Top Page Image Contents