Powermate PM401211 owner manual Fuel Specifications, Consumption Require Ments

Page 13

FUEL SPECIFICATIONS AND

CONSUMPTION REQUIREMENTS

The engine driving the generator is engineered to provide reliable power on either Liquefied Propane Vapor (LPG) or Natural Gas. For proper operation on these fuels, it is important to deliver gas with adequate energy content, at sufficient pressure and flow rate. This is designed to operate on Liquefied Propane Vapor (LPG) with a minimum energy content of 2500 BTU per cubic foot or Natural Gas with a minimum energy content of 1000 BTU per cubic foot. This generator is designed to operate with a fuel pressure at the inlet of the unit between 7 and 11 inches of water column (4-6 ounces).

Required fuel flow rates for specific models are given in the table below. To insure correct sizing of the piping supplying fuel to the generator set, provide the flow and pressure requirements of this section to a fuel supplier or licensed plumber during the installation planning stage. If the fuel supplier cannot guarantee delivery of fuel with these properties, the generator may not perform as advertised.

Due to differences in the energy content of fuel used, it is necessary to derate the output of the generator when connected to Natural Gas. Additionally, regional and/or seasonal variations in the makeup of the fuel can further affect output of the engine/generator system. When using Natural Gas fuel with minimum properties as defined, engine output can fall approximately 10% below that of the same set using Propane Vapor.

FUEL CONSUMPTION TABLE

 

LP Vapor

LP Vapor

Natural Gas

 

(ft 3/hr)

(Gal/hr)

(ft 3/hr)

 

 

 

 

PM401211

81

2.2

186

 

 

 

 

PM409011

79

2.1

176

All values reflect consumption at 100% rated output.

Per the National Gas Code (NFPA 54 - ANSI 2223.1), a manual shutoff valve in the fuel supply line to the generator is recommended.

DANGER

All fuel system installations MUST BE done by a licensed plumber or licensed gas technician and must comply with all applicable codes, standards and regulations.

WARNING

Natural gas (NG) is highly explosive.

Natural gas (NG) is lighter than air and collects in high places.

Liquid propane vapor (LPG) is highly explosive.

Liquid propane vapor (LPG) is heavier than air and collects in lower places.

Extreme caution should be taken when working on a new installation or while performing general maintenance.

Do not smoke when near the unit.

Keep flames, sparks, pilot lights, arc-producing equipment, switches and all other sources of ignition well away. Keep a type ABC fire extinguisher handy.

Potential for fire or explosion always exist when using natural gas (NG) or liquid propane vapor (LPG) as a fuel source. Install this unit in compliance with all local fuel codes.

Do Not operate engine if smell of fuel is present or other explosive conditions exist.

200-2341

13

Image 13
Contents Models PM401211 PM400911 Table of Contents General Safety Guidelines General Safety Guidelines Introductio N Installation Plannin GUnpacking Instruction S Generator Location Utomatic Transfer Switch Placement and Anchoring Generator InstallationInstallation Drawings AIN Line Output Powe R Electrical HookupGfci Circuit Supply Generator Start Signal12KW Wiring Diagram CP200 Controller Consumption Require Ments Fuel SpecificationsNatural Gas NG Fuel HookupPropane Vapor LPG Battery Placement Battery Requirement SConnection Lubrication Nnection con tFirst Time Startup PM401211 PM400911 Generator SpecificationsFuel Alternator SpecificationsIdentificatio N Generator FeatureControl Panel Switches Control Panel FeaturesGenerator Operation Cyclic Crank Starting the GeneratorRUN State ShutdownFaults Status IndicatorsMaintenance Crankcase pressure can blow hot engine oil out Engine OIL Level Chec KEngine OIL and OIL Filter ND Clean INGHange Engine OIL Cooler InspectionEngine AIR Filter Change Battery Maintenanc ETT ERY Maintenanc E con t Fig. G Spark Plug CheckFig. GG Spark Arrestor CleaningEnclosure and Site Governor Speed AdjustmentValve Clearance Check Adjustmen TFuel System Inspection Symptom Possible Cause Corrective Action TroubleshootingSymptom Parts Drawing Exhaust System Parts Drawing Enclosure Parts Drawing LID Assembly Parts Drawing Generator Parts Drawing -H2X Breakdown Parts Drawing Engine Panel END Assembly Parts Drawing Control Panel Breakdown Parts Drawing Battery Hold Down 200-2341 200-2341 Coverage Contact the Coleman Powermate Product Service Department AT 200-2341