Briggs & Stratton 30217 owner manual Assembly, Install Wheel KIT, Remove Generator From Carton

Page 6

5250W Portable Generator

ASSEMBLY

Your generator requires some assembly and is ready for use after it has been properly serviced with the recommended oil and fuel.

If you have any problems with the assembly of your generator, please call the generator helpline at

1-800-743-4115. If calling for assistance, please have the model, revision, and serial number from the data tag available.

Remove Generator From Carton

1.Set carton on a rigid flat surface with “This Side Up” arrows pointing upward.

2.Carefully open top flaps of shipping carton.

3.Cut down corners at one end of carton from top to bottom and lay that side of carton down flat.

4.Remove all packing material, carton fillers, etc.

5.Remove generator from shipping carton.

Carton Contents

Check all contents. If any parts are missing or damaged, call the generator helpline at 1–800–743–4115.

The generator

Generator and engine owner’s manuals

Engine oil

Three packets of fuel stabilizer

Wheel kit

INSTALL WHEEL KIT

NOTE: While the wheel kit is designed to greatly improve the portability of your generator, it is not intended for over-the-road use.

You will need two 1/2” or 13mm open end wrenches or a socket wrench with 1/2" or 13mm sockets and a needle- nose pliers to install this kit.

Refer to Figure 1 and install the wheel kit as follows:

1.Place the bottom of the generator frame on a flat, even surface.Temporarily place unit on blocks to ease assembly.

Figure 1 — Install Wheel Kit

Capscrew

 

 

Nut

 

 

Handle

 

Wheel

 

 

 

 

Washer

 

Axle

 

Mounting Leg

Capscrew

 

 

E-Ring

 

 

 

Nut

 

 

6

 

Image 6
Contents Model / Modelo 030217 5250W Table of Contents Safety RulesEquipment Description When Operating Equipment When Adding or Draining FuelWhen Starting Equipment When Transporting or Repairing EquipmentWhen Adjusting or Making Repairs to Your Generator When Testing for Engine SparkKnow Your Generator Volt AC, 20 Amp, Duplex Receptacle May be120/240 Volt AC, 30 Amp Locking Receptacle May Carton Contents AssemblyInstall Wheel KIT Remove Generator From CartonEngine When Adding FuelBefore Starting Add FuelSystem Ground Using the GeneratorConnecting to a Building’s Electrical System Generator LocationStarting the Engine Connecting Electrical LoadsOperating Generator Stopping the EngineReceptacles 120/240 Volt AC, 30 Amp, Locking ReceptacleVolt AC, 20 Amp, Duplex Receptacle Capacity Power ManagementDont Overload Generator ExampleGenerator Maintenance SpecificationsGeneral Maintenance Recommendations Engine MaintenanceStorage Generator StorageEngine Storage Other Storage Tips Troubleshooting Problem Cause CorrectionLimited Warranty Instrucciones DE Seguridad Tabla DE ContenidosDescripción DEL Equipo AdvertenciaCuando Opere EL Equipo Cuando Añada Combustible O Vacíe EL DepósitoCuando Ponga EN Funcionamiento EL Equipo Cuando Transporte O Repare EL EquipoPrecaución Cuando Ajuste O Haga Reparaciones a SU GeneradorCuando Pruebe LA Bujía DEL Motor Conozca SU Generador Para Retirar el Generador de la Caja MontajeInstale EL Juego DE Ruedas Contenido De La CajaAgregue Combustible Antes DE Darle Arranque AL MotorAgregar Aceite al Motor Cuando Añada CombustibleUbicación del Generador USO DEL GeneradorTierra del Sistema Conexión al Sistema Eléctrico de un EdificioConexion De Cargas Electricas Operando EL Generador PrecauciónEncienda el Motor Parado Del MotorReceptáculos Precaución 120/240 Voltios AC, 30 Amp, Receptáculo de SeguridadVolt AC, 20 Amp, Receptáculo Dobles Control de la Energía No Sobrecargue GeneradorCapacidad EjemploMantenimiento del Motor EspecificacionesRecomendaciones Generales DE Mantenimiento Mantenimiento del GeneradorAlmacenando el Generador Diagnositicos DE AveríasAlmacenamiento Almacenando el MotorGarantía Limitada