Briggs & Stratton 30230 manual Troubleshooting, Problem Cause Correction

Page 14

PowerBOSS™	5600W Portable Generator	TROUBLESHOOTING

TROUBLESHOOTING

	Problem	Cause		Correction

		1.	One of the circuit breakers is	1.	Reset circuit breaker.
			open.
	No AC output is available, but	2.	Fault in generator.	2.	Contact Authorized service facility.
	No AC output is available, but	3.	Poor connection or defective cord	3.	Check and repair.
	generator is running.	3.	Poor connection or defective cord	3.	Check and repair.
	generator is running.		set.
			set.
		4.	Connected device is bad.	4.	Connect another device that is in
					good condition.

	Generator runs good at no-load	1.	Short circuit in a connected load.	1.	Disconnect shorted electrical load.
	Generator runs good at no-load
	but "bogs" down" when loads are	2.	Generator is overloaded.	2.	See "Don't Overload Generator".
	connected.	3.	Shorted generator circuit.	3.	Contact Authorized service facility.
		3.	Shorted generator circuit.	3.	Contact Authorized service facility.

	Generator will not start; or starts	Low oil level.		Fill crankcase to proper level or place
	and runs rough.			generator on level surface.

	Generator shuts down during	1.	Out of fuel.	1.	Fill fuel tank.
	Generator shuts down during	2.	Low oil level.	2.	Fill crankcase to proper level or
	operation.	2.	Low oil level.	2.	Fill crankcase to proper level or
	operation.				place generator on level surface.
					place generator on level surface.

	Generator lacks power.	Load is too high.		See "Don't Overload Generator".

14

Image 14

Contents Model / Modelo 030230 5600W Equipment Description Table of ContentsSafety Rules When Operating Equipment When Adding or Draining FuelWhen Starting Equipment When Transporting or Repairing EquipmentWhen Adjusting or Making Repairs to Your Generator When Testing for Engine SparkKnow Your Generator Install Wheel Kit AssemblyCarton Contents Unpack the GeneratorAdd Engine Oil When Adding FuelBefore Starting the Engine Add FuelSystem Ground Using the GeneratorConnecting to a Building’s Electrical System Generator LocationStarting the Engine Connecting Electrical LoadsOperating Generator Do not Overload the GENERATOR. See Don’t Overload Generator120/240 Volt AC, 30 Amp, Locking Receptacle ReceptaclesStopping the Engine Volt AC, 20 Amp, Duplex ReceptaclesCapacity Power ManagementDont Overload Generator ExampleEngine Maintenance SpecificationsGeneral Maintenance Recommendations Generator MaintenanceEngine Storage StorageGenerator Storage Other Storage TipsTroubleshooting Problem Cause CorrectionLimited Warranty Descripción DEL Equipo Conserve Estas InstruccionesTabla DE Contenidos Reglas DE SeguridadCuando Opere EL Equipo Cuando Añada Combustible O Vacíe EL DepósitoCuando Ponga EN Funcionamiento EL Equipo Cuando Transporte O Repare EL EquipoCuando Pruebe LA Bujía DEL Motor PrecauciónCuando Ajuste O Haga Reparaciones a SU Generador Conozca SU Generador Tapa del Depósito del Aceite Llene el motor con aceiteContenido de la Caja MontajeDesembalaje del Generador Instale el Juego de RuedasAgregue Combustible Antes DE Darle Arranque AL MotorAgregar Aceite al Motor Cuando Añada CombustibleUbicación del Generador USO DEL GeneradorTierra del Sistema Conexión al Sistema Eléctrico de un EdificioConexion De Cargas Electricas Operando EL GeneradorEncienda el Motor No Sobrecargue EL GENERADOR.Vea No Sobrecargue Generador120/240 Voltios AC, 30 Amp, Receptáculo de Seguridad Receptáculos PrecauciónParado Del Motor Volt AC, 20 Amp, Receptáculos DoblesControl de la Energía No Sobrecargue GeneradorCapacidad EjemploMantenimiento del Motor EspecificacionesRecomendaciones Generales DE Mantenimiento Para Limpiar el GeneradorAlmacenando el Generador Diagnositicos DE AveríasAlmacenamiento Almacenando el MotorUso del consumidor Uso comercial