Briggs & Stratton 30230 Operating Generator, Starting the Engine, Connecting Electrical Loads

Page 9

OPERATION

5600W Portable Generator

PowerBOSS™

 

 

 

OPERATING THE

GENERATOR

Starting the Engine

Disconnect all electrical loads from the generator. Use the following start instructions:

1.Make sure unit is on a level surface.

IMPORTANT: Failure to start and operate unit on a level surface will cause the unit not to start or shut down during operation.

2.Turn the fuel valve to the “On” position (Figure 4).The fuel valve handle should be vertical (pointing toward the ground) for fuel to flow.

Figure 4 — Fuel Valve

Fuel Valve is shown in the On position

3.Start engine according to instructions given in the engine operator’s manual.

WARNING

Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

•When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback.

•NEVER start or stop engine with electrical devices plugged in and turned on.

NOTE: If engine starts after 3 pulls but fails to run, or if unit shuts down during operation, make sure unit is on a level surface and check for proper oil level in crankcase.

This unit may be equipped with a low oil protection device. See engine operator’s manual.

WARNING

Running engines produce heat.Temperature of muffler and nearby areas can reach or exceed 150°F (65°C).

Severe burns can occur on contact.

Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire.

•DO NOT touch hot surfaces and avoid hot exhaust gases.

•Allow equipment to cool before touching.

•Keep at least 5 ft. (152 cm) clearance on all sides of generator including overhead.

•Code of Federal Regulation (CFR) Title 36 Parks, Forests, and Public Property require equipment powered by an internal combustion engine to have a spark arrester, maintained in effective working order, complying to USDA Forest service standard 5100-1C or later revision. In the State of California a spark arrester is required under section 4442 of the California Public resources code. Other states may have similar laws.

Connecting Electrical Loads

•Let engine stabilize and warm up for a few minutes after starting.

•Plug in and turn on the desired 120 and/or 240 Volt AC, single phase, 60 Hz electrical loads.

•DO NOT connect 240 Volt loads to the 120 Volt duplex receptacles.

•DO NOT connect 3–phase loads to the generator.

•DO NOT connect 50 Hz loads to the generator.

•DO NOT OVERLOAD THE GENERATOR. See “Don’t Overload Generator”.

CAUTION

Exceeding generators wattage/amperage capacity can damage generator and/or electrical devices connected to it.

•See “Don’t Overload Generator”.

•Start generator and let engine stabilize before connecting electrical loads.

•Connect electrical loads in OFF position, then turn ON for operation.

•Turn electrical loads OFF and disconnect from generator before stopping generator.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Model / Modelo 030230 5600W Table of Contents Safety RulesEquipment Description When Starting Equipment When Adding or Draining FuelWhen Operating Equipment When Transporting or Repairing EquipmentWhen Testing for Engine Spark When Adjusting or Making Repairs to Your GeneratorKnow Your Generator Carton Contents AssemblyInstall Wheel Kit Unpack the GeneratorBefore Starting the Engine When Adding FuelAdd Engine Oil Add FuelConnecting to a Building’s Electrical System Using the GeneratorSystem Ground Generator LocationOperating Generator Connecting Electrical LoadsStarting the Engine Do not Overload the GENERATOR. See Don’t Overload GeneratorStopping the Engine Receptacles120/240 Volt AC, 30 Amp, Locking Receptacle Volt AC, 20 Amp, Duplex ReceptaclesDont Overload Generator Power ManagementCapacity ExampleGeneral Maintenance Recommendations SpecificationsEngine Maintenance Generator MaintenanceGenerator Storage StorageEngine Storage Other Storage TipsProblem Cause Correction TroubleshootingLimited Warranty Tabla DE Contenidos Conserve Estas InstruccionesDescripción DEL Equipo Reglas DE SeguridadCuando Ponga EN Funcionamiento EL Equipo Cuando Añada Combustible O Vacíe EL DepósitoCuando Opere EL Equipo Cuando Transporte O Repare EL EquipoPrecaución Cuando Ajuste O Haga Reparaciones a SU GeneradorCuando Pruebe LA Bujía DEL Motor Tapa del Depósito del Aceite Llene el motor con aceite Conozca SU GeneradorDesembalaje del Generador MontajeContenido de la Caja Instale el Juego de RuedasAgregar Aceite al Motor Antes DE Darle Arranque AL MotorAgregue Combustible Cuando Añada CombustibleTierra del Sistema USO DEL GeneradorUbicación del Generador Conexión al Sistema Eléctrico de un EdificioEncienda el Motor Operando EL GeneradorConexion De Cargas Electricas No Sobrecargue EL GENERADOR.Vea No Sobrecargue GeneradorParado Del Motor Receptáculos Precaución120/240 Voltios AC, 30 Amp, Receptáculo de Seguridad Volt AC, 20 Amp, Receptáculos DoblesCapacidad No Sobrecargue GeneradorControl de la Energía EjemploRecomendaciones Generales DE Mantenimiento EspecificacionesMantenimiento del Motor Para Limpiar el GeneradorAlmacenamiento Diagnositicos DE AveríasAlmacenando el Generador Almacenando el MotorUso comercial Uso del consumidor
Top Page Image Contents