Briggs & Stratton 30230 Before Starting the Engine, Add Engine Oil, Add Fuel, When Adding Fuel

Page 7

ASSEMBLY

5600W Portable Generator

PowerBOSS™

 

 

 

6.Repeat step 4 and 5 to secure second wheel.

7.Tip generator so that engine side is down.

8.Attach support leg with M8 x 20 mm capscrews and M8 lock nuts.

9.Center the handle bracket on generator frame at support leg end of cradle, as shown.

10.Attach handle using two long (M8 x 45mm) cap screws and two locking (M8) hex nuts.Tighten with a 13mm socket and wrench.

11.Return generator to normal operating position (resting on wheels and support leg).

BEFORE STARTING THE ENGINE

Add Engine Oil

• Place generator on a level surface.

CAUTION

Any attempt to crank or start the engine before it has been properly filled with the recommended oil will result in equipment failure.

•Refer to engine operator’s manual for oil fill information.

•Damage to equipment resulting from failure to follow this instruction will void warranty.

•Refer to engine operator’s manual and follow oil recommendations and instructions.

NOTE: Check oil often during engine break–in. Refer to engine operator’s manual for recommendations.

NOTE: The alternator assembly rotates on a prelubricated and sealed ball bearing that requires no additional lubrication for the life of the bearing.

Add Fuel

NOTE: This gasoline engine is certified to operate on

gasoline. Exhaust Emission Control System: EM (Engine Modifications).

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

WHEN ADDING FUEL

•Turn generator OFF and let it cool at least 2 minutes before removing fuel cap. Loosen cap slowly to relieve pressure in tank.

•Fill fuel tank outdoors.

•DO NOT overfill tank. Allow space for fuel expansion.

•Wait for spilled fuel to evaporate before starting engine.

•Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources.

•DO NOT light a cigarette or smoke.

1.Use clean, fresh, regular UNLEADED fuel with a minimum of 87 octane. DO NOT use fuel which contains Methanol. DO NOT mix oil with fuel.

2.Clean area around fuel fill cap, remove cap.

3.Slowly add regular unleaded fuel to fuel tank. Be careful not to overfill. Allow at least 1.5" of tank space for fuel expansion (Figure 2).

Figure 2 - Fuel Expansion

AirSpace

Tank

Fuel

1.5”

 

4.Install fuel cap and let any spilled fuel evaporate before starting engine.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model / Modelo 030230 5600W Safety Rules Table of ContentsEquipment Description When Transporting or Repairing Equipment When Adding or Draining FuelWhen Starting Equipment When Operating EquipmentWhen Testing for Engine Spark When Adjusting or Making Repairs to Your GeneratorKnow Your Generator Unpack the Generator AssemblyCarton Contents Install Wheel KitAdd Fuel When Adding FuelBefore Starting the Engine Add Engine OilGenerator Location Using the GeneratorConnecting to a Building’s Electrical System System GroundDo not Overload the GENERATOR. See Don’t Overload Generator Connecting Electrical LoadsOperating Generator Starting the EngineVolt AC, 20 Amp, Duplex Receptacles ReceptaclesStopping the Engine 120/240 Volt AC, 30 Amp, Locking ReceptacleExample Power ManagementDont Overload Generator CapacityGenerator Maintenance SpecificationsGeneral Maintenance Recommendations Engine MaintenanceOther Storage Tips StorageGenerator Storage Engine StorageProblem Cause Correction TroubleshootingLimited Warranty Reglas DE Seguridad Conserve Estas InstruccionesTabla DE Contenidos Descripción DEL EquipoCuando Transporte O Repare EL Equipo Cuando Añada Combustible O Vacíe EL DepósitoCuando Ponga EN Funcionamiento EL Equipo Cuando Opere EL EquipoCuando Ajuste O Haga Reparaciones a SU Generador PrecauciónCuando Pruebe LA Bujía DEL Motor Tapa del Depósito del Aceite Llene el motor con aceite Conozca SU GeneradorInstale el Juego de Ruedas MontajeDesembalaje del Generador Contenido de la CajaCuando Añada Combustible Antes DE Darle Arranque AL MotorAgregar Aceite al Motor Agregue CombustibleConexión al Sistema Eléctrico de un Edificio USO DEL GeneradorTierra del Sistema Ubicación del GeneradorNo Sobrecargue EL GENERADOR.Vea No Sobrecargue Generador Operando EL GeneradorEncienda el Motor Conexion De Cargas ElectricasVolt AC, 20 Amp, Receptáculos Dobles Receptáculos PrecauciónParado Del Motor 120/240 Voltios AC, 30 Amp, Receptáculo de SeguridadEjemplo No Sobrecargue GeneradorCapacidad Control de la EnergíaPara Limpiar el Generador EspecificacionesRecomendaciones Generales DE Mantenimiento Mantenimiento del MotorAlmacenando el Motor Diagnositicos DE AveríasAlmacenamiento Almacenando el GeneradorUso comercial Uso del consumidor
Top Page Image Contents