Chicago Electric 94678 manual To Start the Engine, To Power 110/120 Volt AC Tools and Equipment

Page 11

To Start the Engine:

1.Make sure the electrical tools/equipment that will be used are not plugged in to the Generator.

2.Turn on the Fuel Valves (9a, 81). Turn the Valve (9a) under the fuel tank to the vertical ON position and swing the Valve (81) on the carburetor behind the Air Filter right to the ON position.

3.Close the Choke Control (80), swinging it to the left.

4.Turn the ON/OFF Switch (52a) to its “ON” position.

5.Hold the Start Handle (64) loosely and pull it slowly several times to allow the gaso- line to flow into the Engine’s carburetor. Then hold the Start Handle firmly and pull the rope hard and fast. Pull the rope all the way out, using two hands if necessary. If necessary pull the rope several times until the Engine starts. The red Pilot Lamp (56a) will illuminate while the generator is able to supply power.

6.Allow the Engine to run for several seconds. Open the Choke Control (80) swing- ing it to the right.

To Power 110/120 Volt AC Tools and Equipment:

1.Prior to powering tools and equipment, make sure the Generator’s rated watt- age capacity (1000 W) is adequate to supply all electrical loads that the unit will power. If powering exceeds the Generator’s capacity, it may be necessary to group one or more of the tools and/or equipment for connection to a separate Generator.

2.Only start the Generator with no loads attached. Once the Generator is running, simply connect the Power Cords of 110/120 volt AC powered tools and equipment into the 110/120 volt AC Outlets (54a).

NOTE: The Generator features an AC Circuit Protector (53a) to protect the AC circuit in case of an overload. Should an overload occur the Breaker will “trip” to its “OFF” position, causing the Generator to automatically shut down and the Pilot Light (56a) on the control panel will shut off to show that the Circuit Protector (53a) has been tripped. For details on preventing this problem, refer to Step #1 above in this section. Then, reset the circuitry system by pressing on the Circuit Protector.

3.When finished using the Generator, turn the ON/OFF Switch (52a) to its “OFF” position. Turn the Fuel Valves (9a, 81) to their “OFF” positions. Then, disconnect all electrical powered tools and equipment from the Generator’s 110/120 volt AC Outlets (53a).

4.After the Engine and Generator have completely cooled, store the Generator in a safe, clean, dry location (if not already installed in one).

SKU 94678

For technical questions, please call 1-800-444-3353.

Page 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents For technical questions or replacement parts, please call HorsepowerUnpacking ContentsSKU 94678 For technical questions, please call SpecificationsSave This Manual Work Area General Safety RulesElectrical Safety Personal SafetyEquipment Use And Care ServiceSpecific Safety Rules Keep the Generator and surrounding area clean at all times Installation PrecautionsFire and Explosion Precautions Electrical Precautions Mechanical PrecautionsGrounding the Generator Installation InstructionsGeneral Location Pre-start Checks Generator Control IllustrationsOperation Instructions To Power 110/120 Volt AC Tools and Equipment To Charge 12 V Lead-acid Type Batteries See maintenance chart on next Inspection, Maintenance, and CleaningProblem Possible Causes Probable Solutions TroubleshootingMaintenance Chart Part Description ’ty Parts List EngineAssembly Diagram Engine Please Read the Following Carefully Parts List a GeneratorRecord Product’s Serial Number Here Assembly Diagram a GeneratorEmission Control System Warranty Warranted Parts Warranty

94678 specifications

The Chicago Electric 94678 is a versatile and efficient tool that stands out in the realm of power tools, particularly for DIY enthusiasts and professional contractors alike. Primarily known as a 7-inch angle grinder, this robust equipment is engineered to handle a variety of tasks, from grinding and cutting to polishing and sharpening. Its powerful performance and ergonomic design make it a popular choice for both heavy-duty jobs and detailed work.

One of the standout features of the Chicago Electric 94678 is its motor capacity. Equipped with a robust 15-amp motor, this angle grinder delivers substantial power for tackling tough materials, including metal and masonry. The motor provides variable speed options, allowing users to adjust the RPM according to the specific requirements of their tasks. This flexibility in speed control is essential for achieving optimal results, whether one is cutting through thick metal or finely grinding edges.

The durability of the Chicago Electric 94678 is another highlight. Built with a rugged housing and designed to withstand the rigors of demanding work environments, this tool is constructed to last. Additionally, it features a spindle lock that facilitates quick and easy wheel changes, allowing users to switch attachments efficiently without requiring additional tools.

In terms of safety, the angle grinder includes protective features that enhance user safety during operation. The protective guard can be adjusted to accommodate different cutting or grinding tasks, minimizing the risk of debris injury. Moreover, the tool is designed with a comfortable grip and lightweight body, reducing user fatigue during prolonged use.

Another noteworthy characteristic of the Chicago Electric 94678 is its compatibility with various accessories and attachments, making it a multifunctional tool. Users can easily attach different grinding wheels, cut-off blades, and polishing pads to expand its capabilities further, making it suitable for a wide range of applications.

Overall, the Chicago Electric 94678 combines power, efficiency, and versatility, positioning it as an invaluable addition to any workshop. Whether for professional use or personal projects, its features and robust design cater to a diverse array of tasks, ensuring it meets the demands of modern-day users.
Top Page Image Contents