Agilent Technologies E4438C Specifications for Analog Modulations, Phase modulation 1, Standard

Page 13

Specifications for Analog Modulations

Phase modulation 1, 2

Resolution

0.1% of set deviation

 

Modulation frequency response 3, 4

 

Standard

 

 

 

Maximum

Allowable rates [3 dB BW]

 

Mode

deviation

FM path 1

FM path 2

 

Normal BW

N x 80 rad

DC to 100 kHz

DC to 100 kHz

 

High BW6

N x 8 rad

(DC to 1 MHz)

(DC to 0.9 MHz)

 

 

N x 1.6 rad

(DC to 10 MHz)

(DC to 0.9 MHz)

With Option UNJ

 

 

 

 

 

Maximum

Allowable rates [3 dB BW]

 

Mode

deviation

FM path 1

FM path 2

 

Normal BW

N x 10 radians

DC to 100 kHz

DC to 100 kHz

 

High BW

N x 1 radians

(DC to 1 MHz)

(DC to 0.9 MHz)

Deviation accuracy [1 kHz rate, Normal BW mode]

< ±5% of deviation + 0.01 radians

Distortion3 [1 kHz rate, deviation < 80 radians on standard model, < 10 N radians on Option UNJ models, Normal BW mode]

< 1%

FM using external inputs 1 or 2

Sensitivity

1 Vpeak for indicated deviation

Input impedance

50 , nominal

Paths

FM path 1 and FM path 2 are summed internally for composite

 

modulation. The FM 2 path is limited to a maximum rate of

 

1 MHz. FM path 2 must be set to a deviation less than the FM

 

path 1.

 

 

Amplitude modulation 1, 6

Range

0 to 100%

 

 

 

 

[fc > 500 kHz]

Resolution

0.1%

 

 

 

 

 

 

Rates [3 dB bandwidth]

 

 

 

DC coupled

0 to 10 kHz

 

 

AC coupled

10 Hz to 10 kHz

 

 

 

 

 

Accuracy 4, 7

1 kHz rate < ±(6% of setting +1%)

 

Distortion 4, 7 [1 kHz rate, THD]

 

 

Option 501-504/Option UNJ

Option 506

 

30% AM

< 1.5%

< 1.5%

 

90% AM

(< 4%)

(< 5%)

 

 

 

 

AM using external inputs 1 or 2

 

 

Sensitivity

1 Vpeak to achieve indicated depth

 

Input impedance

50 , nominal

 

 

Paths

AM path 1 and AM path 2 are summed internally for

 

 

composite modulation.

 

 

 

 

 

1.All analog performance above 4 GHz is typical.

2.For non-Option UNJ units, specifications apply in phase noise mode 2 [default].

3.Refer to frequency bands on page 12 for N.

4.Parentheses denote typical performance.

5.Bandwidth is automatically selected based on deviation.

6.AM is typical above 3 GHz or if wideband AM or I/Q modulation is simultaneously enabled.

7.Peak envelope power of AM must be 3 dB less than maximum output power below 250 MHz.

13

Image 13
Contents Agilent E4438C ESG Vector Signal Generator Table of Contents Introduction E4438C ESG Vector signal generator DefinitionsKey standard features Optional features Key FeaturesFrequency Specifications for Frequency and Power CharacteristicsSweep modes Internal reference oscillator RF reference input requirementsPower Output powerLevel resolution Level range with Attenuator Hold activeLevel accuracy with ALC on Level switching speedOption ±0.15 dB ±0.25 dB Repeatability Repeatability and linearityAmplitude dBm Subharmonics Spectral purityJitter in µUI1, 7 Jitter in seconds1, 7With Option 1E5 Characteristic SSB phase noiseResolution Specifications for Analog ModulationFM using external inputs 1 or Carrier frequency accuracy relative to CW in DCFM3Phase modulation 1 Specifications for Analog ModulationsAmplitude modulation 1 StandardPulse modulation Wideband AMExternal modulation inputs Internal modulation sourceOn/off ratio1 Input voltageRise/fall time1 Minimum burst repetition frequency1Modulation bandwidth Specifications for I/Q CharacteristicsInputs Input impedance Ω or 600 Ω Full scale inputBaseband generator AdjustmentsBaseband outputs Baseband filters ClockReconstruction filter fixed Baseband spectral puritySymbol rate Symbol rate Maximum deviationFrame trigger delay control FIR filterData types Specifications for Signal Personality CharacteristicsInternal burst shape control Spurious emissions Cdma2000Enhanced multitone1 89641A settings Software settings Source settingsWlan 802.11a spectral mask typical performanceCustom digitally modulated signals real-time mode 1 Real-time modeCustom modulation Multiframe output data generation Alternate time slot power level controlPayload bit error count/rate for raw BER Errors in coded channelsContains residual bit errors and bit error count Downlink error reportingGSM/EDGE base station bit error rate test Bert Features Bit error rate BER analyzerClock rate Supported data patternsOperating characteristics Transit case Accessories Inputs and outputsGeneral Characteristics External 1 input Panel SMB connectorsExternal 2 input Allows communication with compatible devicesRelocated to rear panel SMB connectors Opposite in polarity 180 degrees out of phaseSymbol sync input Falling edge is used to clock the data signalWith Option UN7 LAN connectorWith Option File transfer to volatile memoryAuxiliary I/O connector RS-232 connectorMating connector Frequency options Ordering Information1Performance enhancement options E4438C ESG Signal Studio software personalities E4438C ESG signal generation firmware personalitiesRelated Literature Application literaturePage See the ESG Web page for the latest information Agilent Open