Product Specifications, Models and Capacities | Maxtor 5120 specs

SECTION 3

Product Specifications

Models and Capacities

MODEL	92048U8	91792U7	91536U6	91280U5	91024U4	90750U3

Formatted Capacity (MB LBA Mode)	20,480	17,920	15,360	12,800	10,240	7,500

Maxtor defines one megabyte as 106 or one million bytes and one gigabyte as 109 or one billion bytes.

Drive Configuration

MODEL	92048U8	91792U7	91536U6		91280U5	91024U4	90750U3

Integrated Controller / Interface			ATA-5 / Ultra DMA

Encoding Method			EPR4 RLL 16/17

Interleave				1:1

Servo System			Embedded

Buffer Size / Type			2 MB SDRAM

Data Zones per Surface				16

Data Surfaces / Heads	8	7	6		5	4	3

Number of Disks	4	4	3		3	2	2

Areal Density			3.7 Gb / in2

Tracks per Surface (Cylinders)			14,696

Track Density			14,522 tpi

Recording Density			199 - 255 kbpi

Flux Density			211 - 271 kfci

Bytes per Sector / Block			512

Sectors per Track			240 - 401

Sectors per Drive	40,000,464	34,999,776	30,000,096		25,000,416	19,999,728	15,000,048

Performance Specifications

MODEL	92048U8	91792U7	91536U6	91280U5	91024U4	90750U3

Seek Times (typical)

Track-to-Track			1 ms

Average			9.0 ms

Maximum			< 20 ms

Average Latency			4.18 ms

Rotational Speed (±0.1%)			7,200 RPM

Controller Overhead			< 0.5 ms

Data Transfer Rate

To/from Interface			up to 66.7 MB/sec
(Ultra DMA - Mode 2)			up to 66.7 MB/sec
(Ultra DMA - Mode 2)

To/from Interface			up to 16.7 MB/sec
(PIO 4/Multi-word DMA - Mode 2)			up to 16.7 MB/sec
(PIO 4/Multi-word DMA - Mode 2)

To/from Media			up to 32.4 MB/sec

Start Time (0 to Drive Ready)			< 8.8 sec typical

3 – 1

Image 18

Maxtor 5120 manual Product Specifications, Models and Capacities, Drive Configuration, Performance Specifications

Contents

HA RD Drive Produc T MA Nual DiamondMax Plus 92048U8, 91792U7, 91536U6, 91280U5, 91024U4 and 90750U3 Revisions Manual No Before You Begin U T I O N Contents Product Specifications Handling and Installation AT Interface Description Host Software Interface Interface Commands Service and SupportGlossary Figures Manual Organization IntroductionMaxtor Corporation Abbreviations Key Words Signal ConventionsConventions Numbering DiamondMax Plus 5120 Key Features Product Description Product Features Functional / Interface Defect Management Zone DMZ On-the-Fly Hardware Error Correction Code ECCLogical Block Addressing Software ECC Correction Buffer Segmentation Read-Ahead ModeCache Management Automatic Write Reallocation AWR Major HDA Components Cylinder Limitation Subsystem ConfigurationJumper Location/Configuration Dual Drive Support Performance Specifications Product SpecificationsDrive Configuration Models and Capacities Physical Dimensions Parameter Standard Metric EPA Energy Star Compliance Power Requirements AveragePower Mode Definitions Environmental Limits Reliability Specifications Shock and Vibration Safety Regulatory Compliance Radiated Electromagnetic Field Emissions EMC ComplianceCanadian Emissions Statement Pre-formatted Drive Handling and InstallationHard Drive Handling Precautions Important Notice Unpacking and Inspection Multi-pack Shipping Container Physical Installation Recommended Mounting ConfigurationRepacking System Requirements Handling PrecautionsTools for Installation Drive Identification Information General Requirements Hard Drive Identification Installing in a Device Bay Systems Using Cable SelectInstalling 5.25-inch Mounting Brackets and Rails Mounting Drive in System Attaching Interface and Power Cables Attaching System Cables System Setup Setting the Bios CmosBios Cmos Parameters Hard Drive Preparation System Hangs During Boot Interface Connector AT Interface DescriptionPin Description Summary PIN Name Signal Name Signal Description Pin Description Table Timing Parameters Mode PIO Timing DMA Timing Mode MIN MAX Ultra DMA Timing Sustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst Host Software Interface Error RegisterFeatures Register Task File Registers Cylinder Number Registers Sector Count RegisterSector Number Register Device/Head Register Command Register Command Name Command Code Parameters Used SDH Summary Device Control Register Control Diagnostic RegistersAlternate Status Register Digital Input Register Reset and Interrupt Handling Reset HandlingInterrupt Handling Interface Commands Set Feature Commands Read Commands Read SectorsRead Verify Sectors Read DMA Read Multiple Write Sectors Write CommandsSet Multiple Mode Write Verify Sectors Write Multiple Write DMA Set Feature Commands Set Features Mode Power Mode Commands Sleep Mode Initialization Commands Identify Drive 15-8 = PIO data transfer mode = Write Cache enabled Initialize Drive Parameters Seek, Format and Diagnostic Commands Execute Drive DiagnosticFormat Track A.R.T. Command Set Execute S.M.A.R.T No Quibble Service Service and SupportService Policy Support MaxFax Service Customer ServiceInternet Access Time Glossary Cylinder Zero Gigabyte GB Logical Block Addressing Read Gate Signal THIN-FILM Media