Physical Dimensions, Parameter Standard Metric | Maxtor 5120

PRODUCTSPECIFICATIONS

Physical Dimensions

PARAMETER	STANDARD	METRIC
Height	1.02 inches	25.9 millimeters
Length	5.78 inches	146.6 millimeters
Width	4.00 inches	102.1 millimeters
Weight	1.3 pounds	0.59 kilograms

1.028 max

[25.9 mm]


	6 x 6-32			1.638 ± .005		1.122 ± .02


	UNC Tap			[41.61 mm]		[28.4 mm]

4.000 ± .01

[101.6 mm]

5.787 max

[146.6 mm]

4 x 6-32

1.75 ± .02

1.625 ± .02

UNC Tap

.25 ± .01

4.00 ± .01

[102.1 mm]

3.75± .01 [95.25 mm]

Figure 3 - 1

Outline and Mounting Dimensions

3 – 2

Image 19

Maxtor 5120 manual Physical Dimensions, Parameter Standard Metric

Contents

HA RD Drive Produc T MA Nual 92048U8, 91792U7, 91536U6, 91280U5, 91024U4 and 90750U3 DiamondMax Plus Revisions Manual No U T I O N Before You Begin Contents Handling and Installation Product Specifications Host Software Interface AT Interface Description Service and Support Interface CommandsGlossary Figures Abbreviations IntroductionMaxtor Corporation Manual Organization Numbering Signal ConventionsConventions Key Words Product Description DiamondMax Plus 5120 Key Features Functional / Interface Product Features Software ECC Correction On-the-Fly Hardware Error Correction Code ECCLogical Block Addressing Defect Management Zone DMZ Automatic Write Reallocation AWR Read-Ahead ModeCache Management Buffer Segmentation Major HDA Components Dual Drive Support Subsystem ConfigurationJumper Location/Configuration Cylinder Limitation Models and Capacities Product SpecificationsDrive Configuration Performance Specifications Parameter Standard Metric Physical Dimensions Environmental Limits Power Requirements AveragePower Mode Definitions EPA Energy Star Compliance Shock and Vibration Reliability Specifications Radiated Electromagnetic Field Emissions EMC Compliance Safety Regulatory ComplianceCanadian Emissions Statement Important Notice Handling and InstallationHard Drive Handling Precautions Pre-formatted Drive Multi-pack Shipping Container Unpacking and Inspection Recommended Mounting Configuration Physical InstallationRepacking Drive Identification Information Handling PrecautionsTools for Installation System Requirements Hard Drive Identification General Requirements Mounting Drive in System Systems Using Cable SelectInstalling 5.25-inch Mounting Brackets and Rails Installing in a Device Bay Attaching System Cables Attaching Interface and Power Cables Setting the Bios Cmos System SetupBios Cmos Parameters Hard Drive Preparation System Hangs During Boot AT Interface Description Interface ConnectorPin Description Summary Pin Description Table PIN Name Signal Name Signal Description PIO Timing Timing Parameters Mode DMA Timing Ultra DMA Timing Mode MIN MAX Sustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst Task File Registers Error RegisterFeatures Register Host Software Interface Device/Head Register Sector Count RegisterSector Number Register Cylinder Number Registers Command Register Summary Command Name Command Code Parameters Used SDH Digital Input Register Control Diagnostic RegistersAlternate Status Register Device Control Register Reset Handling Reset and Interrupt HandlingInterrupt Handling Set Feature Commands Interface Commands Read Sectors Read CommandsRead Verify Sectors Read Multiple Read DMA Write Verify Sectors Write CommandsSet Multiple Mode Write Sectors Write DMA Write Multiple Set Features Mode Set Feature Commands Power Mode Commands Sleep Mode Identify Drive Initialization Commands 15-8 = PIO data transfer mode = Write Cache enabled Initialize Drive Parameters Execute Drive Diagnostic Seek, Format and Diagnostic CommandsFormat Track Execute S.M.A.R.T A.R.T. Command Set Support Service and SupportService Policy No Quibble Service Customer Service MaxFax ServiceInternet Glossary Access Time Cylinder Zero Gigabyte GB Logical Block Addressing Read Gate Signal THIN-FILM Media