MTD E760, E740 manual Operation, GAS and OIL FILL-UP, To Start Engine

Page 11

SECTION 7: OPERATION

GAS AND OIL FILL-UP

Service the engine with gasoline and oil as instructed in the separate engine manual packed with your snow thrower. Read instructions carefully.

WARNING: Never fill fuel tank indoors, with engine running or while engine is hot. Do not smoke when filling fuel tank.

Electric Starter

WARNING: The electric starter is equipped with a three-wire power cord and plug, and is designed to operate on 120 volt AC household current. It must be properly grounded at all times to avoid the possibility of electric shock which may be injurious to the operator. Follow all instructions carefully. Determine that your house wiring is a three-wire grounded system. Ask a licensed electrician if you are not certain. If your house wiring system is not a three-wire grounded system, do not use this electric starter under any conditions. If your system is grounded and a three-hole receptacle is not available at the point your starter will normally be used, one should be installed by a licensed electrician.

When connecting the power cord, always connect cord to starter on engine first, then plug the other end into a three-hole grounded receptacle.

When disconnecting the power cord, always unplug the end from the three-hole grounded receptacle first.

TO START ENGINE

IMPORTANT: If unit shows any sign of motion (drive or augers) with the clutch grips disengaged, shut engine off immediately. Readjust as instructed in the “Final Adjustments” section of the Assembly Instructions.

Ignition

Key

 

Starter

Choke

Handle

Primer

Throttle

 

Figure 16

 

1.Attach spark plug wire to spark plug.

2.Make certain the fuel shut-off valve is in the open (vertical) position.

3.Make certain the auger drive and traction drive clutch grips are in the disengaged (released) position.

4.Move throttle control up to FAST position. Insert ignition key into slot. See figure 16. Be certain it snaps into place. Do not turn key.

5.Rotate choke knob to FULL choke position (cold engine start).

6.If engine is warm, place choke in OFF position instead of FULL.

7.Connect power cord to switch box on engine. Plug the other end of power cord into a three- hole, grounded 120 volt AC receptacle.

8.Recoil Start Only: Push primer button two or three times. If engine is warm, push primer button once only. See figure 16.

NOTE: Always cover vent hole in primer button when pushing. Additional priming may be necessary for first start if temperature is below 15oF.

9.Electric Start: Push starter button on top of the engine to crank the engine. When engine starts, release starter button.

Recoil Start: Grasp starter handle (see figure 16) and pull rope out slowly, until it pulls slightly harder. Let rope rewind slowly. Pull starter handle rapidly. Do not allow handle to snap back. Allow it to rewind slowly while keeping a firm hold on the starter handle.

10.Repeat step 9 until engine starts. If engine fails to start, repeat steps 8 and 9 until engine starts.

11.As engine warms up and begins to operate evenly, rotate choke knob slowly to OFF position. If engine falters, return to FULL choke, then slowly move to OFF position.

AVOID INJURY FROM ROTATING

AUGER — KEEP HANDS, FEET

AND CLOTHING AWAY.

5785

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents MTD Products INC. P.O. BOX 368022 CLEVELAND, Ohio Important Read Safety Rules and Instructions CarefullyOperation Important Safe Operation PracticesTraining PreparationSafety labels found on your snow thrower Maintenance and StorageCalling Customer Support Finding Your Model NumberContents of Hardware Pack Unpacking Assembly InstructionsAttaching the Handle Assembly Hardware C Attaching the Chute AssemblyAttaching the Chute Crank Hardware BHardware D Attaching the Shift RODAttaching the Clutch Cables Attaching the Track ControlsFinal Adjustments Track Lock Lever ControlsAuger Drive Clutch Left and Right Track ControlsIgnition Key Starter Choke Handle Primer Throttle OperationGAS and OIL FILL-UP To Start EngineOperating Tips To Stop EngineTo Engage Drive To Engage AugersAdjustments Lubrication Drive Belt MaintenanceAuger Belts Drive Belt Changing the Friction Wheel RubberFriction DiscOFF-SEASON Storage Trouble Possible Causes Corrective Action Trouble Shooting GuideGear Assembly Handle Assembly Handle Assembly Blower Housing 26’’ Track and Frame Track and Frame Description Qty Engine and V-Belts Page MANUFACTURER’S Limited Warranty for

E760, E740 specifications

The MTD E740 and E760 represent a significant advancement in outdoor power equipment, particularly in the realm of lawn care and maintenance. Both models are designed to cater to the needs of homeowners and professionals alike, providing them with reliable, efficient, and user-friendly mowing solutions.

One of the main features of the MTD E740 and E760 is their robust 21-inch steel cutting deck. This durable construction ensures that the mower can withstand the rigors of frequent use, while also delivering a precise cutting performance. The wide cutting deck allows for efficient mowing of larger lawns, reducing the time and effort required to achieve a pristine lawn.

Both models are equipped with powerful engines designed for optimal performance. The E740 comes with a reliable 196cc engine, while the E760 boasts an enhanced 224cc engine, providing even more power for tackling thick grass and challenging terrain. This increased engine capacity not only improves cutting performance but also enhances the longevity of the mower, ensuring that it can handle a variety of conditions over time.

Another noteworthy technology featured in both the E740 and E760 is the advanced mulching capability. Mulching allows grass clippings to be finely chopped and redistributed back onto the lawn, providing essential nutrients to the soil. This eco-friendly feature not only promotes a healthier lawn but also eliminates the need for bagging clippings, making lawn maintenance more convenient.

User comfort is also a primary consideration in the design of these mowers. Both the E740 and E760 feature ergonomic handles that are adjustable, allowing users to customize their mowing experience for maximum comfort. The models also include easy-to-use height adjustment systems, enabling operators to choose from multiple cutting heights with just a simple lever move.

In terms of maneuverability, both mowers are designed for ease of use. They feature robust wheels that provide excellent traction on various surfaces, making it easier to navigate around obstacles and uneven terrain. Additionally, the lightweight design of these mowers means that they can be easily transported and stored.

Overall, the MTD E740 and E760 combine power, precision, and convenience, making them excellent choices for homeowners looking to maintain a well-groomed lawn with minimal effort. Their blend of advanced technologies and user-friendly features ensures that mowing can be a more enjoyable and efficient task.
Top Page Image Contents