Poulan PP10527ES, 420923 Loop Handle LH, Loop Handle RH, Lower Handle, Pivot Support Weldment

Page 26

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP10527ES (96192002000)

HANDLES

5 5

KEY	PART	DESCRIPTION	4
NO.	NO.	DESCRIPTION
1	419798X479	LOOP HANDLE LH	2
2	419799X479	LOOP HANDLE RH	2
2	419799X479	LOOP HANDLE RH
3	74780524	SCREW 5/16−18 X 1.50
4	74780528	SCREW 5/16−18 X 1.75
5	751153	NUT 5/16−18

01.08.004-A

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	419797X479	LOWER HANDLE
2	405784X479	PIVOT SUPPORT WELDMENT
3	17490508	SCREW 5/16−18 X .50
4	17000616	SCREW 3/8−16 X 1.00

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 26

Image 26

Contents Rev 1 08.08.08 SBW/TH Model NumberSnow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonRemove plastic tie securing rod to lower handle Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYAuger control lever used to engage auger motion throw snow Meets A.N.S.I. Safety RequirementsDeflector remote control lever used to change Distance the snow is thrownHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig Release the auger control lever and shut off the engineCheck Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine ADD Gasoline See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Exploded KEY Part Description Auger Bearing Auger HousingScraper BAR Bearing Plug420496X421 420495X421Auger 27 LH Auger 27 RHDeflector Weldment Deflector Control AssemblyChute Weldment Deflector SealRotator Pivot Bracket LEVER/CABLE Rotator AssemblyRotator Head Pulley PivotLower Handle Loop Handle LHLoop Handle RH Pivot Support WeldmentKnob RED SpacerRetainer Handle KnobShifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD BottomHeadlight Bezel Wire HarnessConsole Panel Flood HeadlightRepair Parts Snow Thrower - Model Number PP10527ES Drive END Plate Speed Selector AssemblyDrive Plate Assembly Bottom PAN01.03.002-A 409346X428 Frame KEY Part Description ENGINE, TECModel LH358SA-159628A 417014X428 Engine Mount PlateImpeller Belt Belt CoverTraction Belt Repair Parts Snow Thrower - Model Number PP10527ES Wheels Cable Bracket LH Cable Bracket RHWheel Lobe CoverWheel Driver Retainer Ring Clutch SlideSafety Ignition KEY 35062DECAL, Poulan PRO DECAL, DANGER, Deflector 181037DECAL, Danger DECAL, DangerService Notes Limited Warranty

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP10527ES (96192002000)

HANDLES

KEY

LOOP HANDLE LH

LOOP HANDLE RH

KEY

LOWER HANDLE

PIVOT SUPPORT WELDMENT