Poulan 420923, 96192002000, PP10527ES Parts Packed Separately in Carton, Assembly / PRE-OPERATION

Page 4

PARTS PACKED SEPARATELY IN CARTON

(1) AUGER CONTROL ROD

(1) TRACTION DRIVE CONTROL ROD

(1) MULTI-

WRENCH

(180684)

(2) FLAT WASHERS

 

(1) POWER CORD

 

(1) DISCHARGE CHUTE

(198563)

(3) RETAINER

 

 

 

 

 

SPRINGS

 

 

(169675)

ROTATOR HEAD MOUNTING

(2) CARRIAGE BOLTS 3/8-16 x 2.25

(1) WASHER 3/8

(1) LOCKNUT 3/8

(1) SAFTEY IGNITION KEY

(35062)

(19131316)

(73800600)

 

(2) HANDLE KNOBS

EXTRA SHEAR BOLTS AND NUTS

(2) SHEAR BOLTS 1/4-20 x 1-3/4

(2) SPACERS

(2) LOCKNUTS

(198636)

(198638)

1/4-20

 

 

(73800400)

ASSEMBLY / PRE-OPERATION

Read these instructions and this manual in its entirety

 

2.

Cut down all four corners of carton and lay panels flat.

before you attempt to assemble or operate your new

 

3.

Remove the two (2) screws securing the auger housing

snow thrower. Reading the entire manual will familiar-

 

 

 

to the pallet.

ize you with the unit, which will assist you in assembly,

 

 

 

4.

Remove all packing materials except plastic tie holding

operation and maintenance of the product.

 

 

 

speed control rod to lower handle.

Your new snow thrower has been assembled at the factory

 

 

 

5. Remove the two (2) plastic ties securing the upper

with the exception of those parts left unassembled for ship-

 

 

 

handle to the pallet.

ping purposes. All parts such as nuts, washers, bolts, etc.,

 

 

 

6. Remove snow thrower from carton and check carton

necessary to complete the assembly have been placed in

 

the parts bag. To ensure safe and proper operation of your

 

 

thoroughly for additional loose parts.

snow thrower, all parts and hardware you assemble must

 

HOW TO SET UP YOUR SNOW THROWER

be tightened securely. Use the correct tools as necessary

 

to ensure proper tightness.

 

TOOL BOX (See Fig. 10)

 

 

REMOVE SNOW THROWER FROM CARTON

 

A toolbox is provided on your snow thrower. The toolbox is

1. Remove all accessible loose parts and parts boxes

 

located on top of the belt cover. Store the extra shear bolts,

4

nuts and multi-wrench provided in parts bag in the toolbox.

from carton.

 

 

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Snow Thrower Model NumberRev 1 08.08.08 SBW/TH Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsRemove plastic tie securing rod to lower handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Deflector remote control lever used to changeAuger control lever used to engage auger motion throw snow Distance the snow is thrownHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig Release the auger control lever and shut off the engineTo Adjust Skid Plates See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Exploded KEY Part Description Auger Housing Scraper BARAuger Bearing Bearing Plug420495X421 Auger 27 LH420496X421 Auger 27 RHDeflector Control Assembly Chute WeldmentDeflector Weldment Deflector SealLEVER/CABLE Rotator Assembly Rotator HeadRotator Pivot Bracket Pulley PivotLoop Handle LH Loop Handle RHLower Handle Pivot Support WeldmentSpacer RetainerKnob RED Handle KnobImpeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD BottomWire Harness Console PanelHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number PP10527ES Drive Speed Selector Assembly Drive Plate AssemblyEND Plate Bottom PAN01.03.002-A KEY Part Description ENGINE, TEC Model LH358SA-159628A409346X428 Frame 417014X428 Engine Mount PlateTraction Belt Belt CoverImpeller Belt Repair Parts Snow Thrower - Model Number PP10527ES Wheels Cable Bracket LH Cable Bracket RHCover Wheel Driver Retainer RingWheel Lobe Clutch SlideSafety Ignition KEY 35062181037 DECAL, DangerDECAL, Poulan PRO DECAL, DANGER, Deflector DECAL, DangerService Notes Limited Warranty
Top Page Image Contents