Poulan 420923, 96192002000, PP10527ES owner manual 35062, Safety Ignition KEY

Page 37

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP10527ES (96192002000)

BAG OF PARTS

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	198563	POWER CORD
2	169675	RETAINER PIN
3	180684	WRENCH
4	184505	REMOTE SPRING

5179829 SHOULDER BOLT 1/4−20

6179246 NYLON WASHER 1/4−20

7191730 LOCKNUT 1/4−20

4
5	6	7
5

8	9

10 11

1		14
1		13
		13
	12	01.14.003-A
KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

872250505 CARRIAGE BOLT 5/16−18 X 5/8

9751153 LOCKNUT 5/16−18

1073800600 LOCKNUT 3/8−16

11	19131316	WASHER 3/8
12	198636	SHEAR BOLT 1/4−20 X 1−3/4
13	198638	SPACER
14	73800400	LOCKNUT 1/4−20

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	35062	SAFETY IGNITION KEY

01.14.008-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Image 37

Contents Snow Thrower Model NumberRev 1 08.08.08 SBW/TH Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsRemove plastic tie securing rod to lower handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer Ignition KEYDeflector remote control lever used to change Meets A.N.S.I. Safety RequirementsAuger control lever used to engage auger motion throw snow Distance the snow is thrownStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Release the auger control lever and shut off the engineBefore Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Exploded KEY Part Description Scraper BAR Auger HousingAuger Bearing Bearing PlugAuger 27 LH 420495X421420496X421 Auger 27 RHChute Weldment Deflector Control AssemblyDeflector Weldment Deflector SealRotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley PivotLoop Handle RH Loop Handle LHLower Handle Pivot Support WeldmentRetainer SpacerKnob RED Handle KnobTraction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomConsole Panel Wire HarnessHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number PP10527ES Drive Drive Plate Assembly Speed Selector AssemblyEND Plate Bottom PAN01.03.002-A Model LH358SA-159628A KEY Part Description ENGINE, TEC409346X428 Frame 417014X428 Engine Mount PlateTraction Belt Belt CoverImpeller Belt Cable Bracket LH Cable Bracket RH Repair Parts Snow Thrower - Model Number PP10527ES WheelsWheel Driver Retainer Ring CoverWheel Lobe Clutch Slide35062 Safety Ignition KEYDECAL, Danger 181037DECAL, Poulan PRO DECAL, DANGER, Deflector DECAL, DangerService Notes Limited Warranty

KEY

KEY

WASHER 3/8

SPACER

KEY

35062

SAFETY IGNITION KEY