Poulan 420923, 96192002000 Install Chute Deflector Remote Control See Figs, Check Tire Pressure

Page 7

ASSEMBLY / PRE-OPERATION

INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9)

1.Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely.

2.Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt, nylon washer and 1/4-20 locknut as shown. Tighten securely.

3.Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown.

	1/4-20	SPRING
	1/4-20	CHUTE
	SHOULDER	CHUTE
	SHOULDER	DEFLECTOR
	BOLT	DEFLECTOR
	BOLT
		HOOK
	NYLON	BETWEEN
	WASHER	HEX NUTS
		ON CHUTE
	1/4-20	ROTATER
	LOCKNUT	HEAD
		5/16-18
		CARRIAGE
		BOLT
	CABLE
	EYELET
	REMOTE
	CABLE
	BRACKET
	5/16-18
	LOCKNUT

FIG. 8

CHUTE DEFLECTOR

CONTROL LEVER

FIG. 9

CHECK TIRE PRESSURE

The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pressure is important for best snow throwing performance.

•Reduce tire pressure to 14-17 PSI (19-24.5 N-m).

Image 7

Contents Snow Thrower Model NumberRev 1 08.08.08 SBW/TH Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonUnfold Upper Handle Install Speed Control ROD See FigsRemove plastic tie securing rod to lower handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerDistance the snow is thrown Meets A.N.S.I. Safety RequirementsDeflector remote control lever used to change Auger control lever used to engage auger motion throw snowStopping HOW to USE Your Snow ThrowerRelease the auger control lever and shut off the engine Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigADD Gasoline See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Exploded KEY Part Description Bearing Plug Auger HousingScraper BAR Auger BearingAuger 27 RH 420495X421Auger 27 LH 420496X421Deflector Seal Deflector Control AssemblyChute Weldment Deflector WeldmentPulley Pivot LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketPivot Support Weldment Loop Handle LHLoop Handle RH Lower HandleHandle Knob SpacerRetainer Knob REDShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPFlood Headlight Wire HarnessConsole Panel Headlight BezelRepair Parts Snow Thrower - Model Number PP10527ES Drive Bottom PAN Speed Selector AssemblyDrive Plate Assembly END Plate01.03.002-A 417014X428 Engine Mount Plate KEY Part Description ENGINE, TECModel LH358SA-159628A 409346X428 FrameTraction Belt Belt CoverImpeller Belt Cable Bracket LH Cable Bracket RH Repair Parts Snow Thrower - Model Number PP10527ES WheelsClutch Slide CoverWheel Driver Retainer Ring Wheel Lobe35062 Safety Ignition KEYDECAL, Danger 181037DECAL, Danger DECAL, Poulan PRO DECAL, DANGER, DeflectorService Notes Limited Warranty