Poulan PP10527ES Console Panel, Headlight Bezel, Flood Headlight, SHOULDERSCREW10−24X.625, Bulb

Page 29

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP10527ES (96192002000)

HANDLES

7	4

	3			5
	2			KEY	PART	DESCRIPTION
				NO.	NO.	DESCRIPTION
				1	182906	CONSOLE PANEL
			1	2	178668	HEADLIGHT BEZEL
	5	4	1	3	180927	FLOOD HEADLIGHT
6		4		4	184471	SHOULDERSCREW10−24X.625
				4	184471	SHOULDERSCREW10−24X.625
				5	175262	SCREW 10−24 X 1.25
				5	175262	SCREW 10−24 X 1.25
				6	178770	WIRE HARNESS
				7	183784	BULB
		01.10.007-B

5	2	KEY	PART
	2	NO.	NO.	DESCRIPTION
		NO.	NO.	DESCRIPTION
		1	412675X004	INTERLOCK SPRING
	1	2	414572	INTERLOCK CAM
	1	3	178831	TORSION SPRING
		4	169675	RETAINER
		5	17060410	SCREW 1/4−20 X .625
		6	421252	INTERLOCK STOP
	6	01.08.007-B

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 29

Image 29

Contents Rev 1 08.08.08 SBW/TH Model NumberSnow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonRemove plastic tie securing rod to lower handle Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer Ignition KEYDeflector remote control lever used to change Meets A.N.S.I. Safety RequirementsAuger control lever used to engage auger motion throw snow Distance the snow is thrownStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Release the auger control lever and shut off the engineBefore Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Exploded KEY Part Description Scraper BAR Auger HousingAuger Bearing Bearing PlugAuger 27 LH 420495X421420496X421 Auger 27 RHChute Weldment Deflector Control AssemblyDeflector Weldment Deflector SealRotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley PivotLoop Handle RH Loop Handle LHLower Handle Pivot Support WeldmentRetainer SpacerKnob RED Handle KnobTraction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomConsole Panel Wire HarnessHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number PP10527ES Drive Drive Plate Assembly Speed Selector AssemblyEND Plate Bottom PAN01.03.002-A Model LH358SA-159628A KEY Part Description ENGINE, TEC409346X428 Frame 417014X428 Engine Mount PlateImpeller Belt Belt CoverTraction Belt Cable Bracket LH Cable Bracket RH Repair Parts Snow Thrower - Model Number PP10527ES WheelsWheel Driver Retainer Ring CoverWheel Lobe Clutch Slide35062 Safety Ignition KEYDECAL, Danger 181037DECAL, Poulan PRO DECAL, DANGER, Deflector DECAL, DangerService Notes Limited Warranty

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP10527ES (96192002000)

KEY

CONSOLE PANEL

HEADLIGHT BEZEL

FLOOD HEADLIGHT

SHOULDERSCREW10−24X.625

WIRE HARNESS

BULB

KEY

INTERLOCK SPRING

INTERLOCK CAM

TORSION SPRING

RETAINER

INTERLOCK STOP