Poulan 421895, 96192001904 owner manual Engine, Cleaning

Page 15

MAINTENANCE

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Chute Deflector Remote ControlUnfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineDrive speed control lever used to select forward or Stopping HOW to USE Your Snow ThrowerTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigADD Gasoline See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Remove Wheels See Fig To Replace Belts See FigOther StorageTroubleshooting Auger Bearing Auger HousingKEY Part Description Scrapper BARSkid Plate RH Auger Assembly 30 LHAuger Assembly 30 RH Skid Plate LHExploded Impeller Pulley Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool BearingWasher Weight BAR181160X479 Drift Cutter BAR Plastic WasherDeflector Seal Deflector Control AssemblyChute Weldment Deflector WeldmentKEY Part Repair Parts Snow Thrower Model PP11530ES Handles Pivot Support Loop Handle LHLoop Handle RH Lower TubeHandle Knob Repair PartsSpacer Knob REDCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Drive Axle ShaftSprocket Repair Parts Snow Thrower Model PP11530ES Drive Bottom PAN Speed Selector AssemblyDrive Plate Assembly END PlateENGINE, TEC FrameEngine Mount Plate Belt Cover Traction BeltImpeller Belt 196753X421 Repair Parts Snow Thrower Model PP11530ES WheelsWheel Assembly LH 196752X421Clutch Slide CoverWheel Driver Retainer Ring Wheel LobeShear Bolt KIT Repair Parts Snow Thrower Model PP11530ES BAG of PartsSafety Ignition KEY WrenchRepair Parts Snow Thrower Model PP11530ES Decals Limited Warranty

96192001904, 421895 specifications

The Poulan 421895,96192001904 is a powerful chainsaw designed for both residential and professional use. Known for its robust construction and cutting efficiency, this model is widely recognized among tree care professionals and homeowners. It provides an ideal balance of power, ease of use, and durability, making it an essential tool for various cutting tasks, from trimming branches to felling trees.

One of the main features of the Poulan 421895 is its engine performance. It typically comes equipped with a reliable two-stroke engine that delivers impressive horsepower, ensuring efficient cutting capability for a variety of applications. The engine is designed for easy starting, which minimizes user frustration and enhances productivity. Additionally, the engine is built with lower emissions technology, aligning with environmental standards while reducing the carbon footprint.

The design of the Poulan 421895 includes an ergonomic handle that increases comfort during extended use. This feature is particularly beneficial for professionals who may spend long hours operating the tool. The chainsaw also includes anti-vibration technology, which helps reduce fatigue and improve control, making it easier to maneuver during cutting tasks.

Safety is a paramount concern in chainsaw operation, and the Poulan 421895 addresses this through several built-in safety features. It is equipped with a chain brake that stops the chain quickly in case of kickback, providing an added layer of protection for the user. Furthermore, the chainsaw incorporates a safety lock that prevents accidental starting, ensuring that users can operate the tool with peace of mind.

User maintenance is also a key focus of the Poulan 421895. The chainsaw features an automatic oiling system that keeps the chain lubricated during operation, prolonging the life of both the chain and the guide bar. This system reduces the need for frequent manual maintenance, allowing users to focus more on their work rather than upkeep.

In conclusion, the Poulan 421895,96192001904 is a versatile and efficient chainsaw that meets the needs of various users, from weekend warriors to seasoned professionals. With its powerful engine, ergonomic design, safety features, and low maintenance requirements, it stands out as a reliable choice for anyone in need of a dependable cutting tool. Whether tackling yard work or larger tree care projects, this chainsaw is built to deliver consistent performance.
Top Page Image Contents