Poulan 421895, 96192001904 owner manual Table of Contents

Page 3

6.When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impel- ler and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the engine.

7.Do not run the engine indoors, except when starting the engine and for transporting the snow thrower in or out of the building. Open the outside doors; exhaust fumes are dangerous.

8.Exercise extreme caution when operating on slopes.

9.Never operate the snow thrower without proper guards, and other safety protective devices in place and work- ing.

10.Never direct the discharge toward people or areas where property damage can occur. Keep children and others away.

11.Do not overload the machine capacity by attempting to clear snow at too fast a rate.

12.Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when operating in reverse.

13.Disengage power to the collector/impeller when snow thrower is transported or not in use.

14.Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counterweights, or cabs).

15.Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run.

16. Never touch a hot engine or muffler.

Clearing a Clogged Discharge Chute

Hand contact with the rotating impeller inside the discharge chute is the most common cause of injury associated with snow throwers. Never use your hand to clean out the dis- charge chute. To clear the chute:

1.SHUT THE ENGINE OFF!

2.Wait 10 seconds to be sure the impeller blades have stopped rotating.

3.Always use a clean-out tool, not your hands.

Maintenance and Storage

1.Check shear bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

2.Never store the machine with fuel in the fuel tank inside a building where ignition sources are present such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing in any enclosure.

3.Always refer to operator’s manual for important details if the snow thrower is to be stored for an extended period.

4.Maintain or replace safety and instruction labels, as necessary.

5.Run the machine a few minutes after throwing snow to prevent freeze-up of the collector/impeller.

CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and manu- factured to give best possible dependability and perfor- mance.

Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. We have competent, well-trained technicians and the proper tools to service or repair this unit.

Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower properly. Always observe the “SAFETY RULES”.

SERIAL NUMBER: ___________________________

DATE OF PURCHASE: _______________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A DECAL ATTACHED TO THE REAR OF THE SNOW THROWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

PRODUCT SPECIFICATIONS

Gasoline Capacity 4.0 Quarts (3,79 Liters)

and Type: Unleaded Regular only

Oil Type

SAE 30 (above 40°F)

(API SG–SL):

SAE 5W-30 or 10W-30 (0° to +40°F)

 

SAE 0W-30 (below 0°F)

 

 

Oil Capacity:

26 Ounces (0,7 Liters)

 

 

Spark Plug

Champion RJ19LM

Gap:

0.030" (0,762 mm)

CUSTOMER RESPONSIBILITIES

•Read and observe the safety rules.

•Follow a regular schedule in maintaining, caring for and using your snow thrower.

•Follow the instructions under “Maintenance” and “Stor- age” sections of this owner’s manual.

TABLE OF CONTENTS

SAFETY RULES

2-3

PRODUCT SPECIFICATIONS

3

CUSTOMER RESPONSIBILITIES

3

ASSEMBLY / PRE-OPERATION

5-7

OPERATION

8-13

MAINTENANCE SCHEDULE

14

MAINTENANCE

14-15

SERVICE AND ADJUSTMENTS

16-18

STORAGE

18

TROUBLESHOOTING

19

REPAIR PARTS

20-39

3 WARRANTY

40

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Chute Deflector Remote ControlUnfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineDrive speed control lever used to select forward or Stopping HOW to USE Your Snow ThrowerTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigADD Gasoline See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Remove Wheels See Fig To Replace Belts See FigOther StorageTroubleshooting Auger Bearing Auger HousingKEY Part Description Scrapper BARSkid Plate RH Auger Assembly 30 LHAuger Assembly 30 RH Skid Plate LHExploded Impeller Pulley Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool BearingWasher Weight BAR181160X479 Drift Cutter BAR Plastic WasherDeflector Seal Deflector Control AssemblyChute Weldment Deflector WeldmentKEY Part Repair Parts Snow Thrower Model PP11530ES Handles Pivot Support Loop Handle LHLoop Handle RH Lower TubeHandle Knob Repair PartsSpacer Knob REDCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Drive Axle ShaftSprocket Repair Parts Snow Thrower Model PP11530ES Drive Bottom PAN Speed Selector AssemblyDrive Plate Assembly END PlateENGINE, TEC FrameEngine Mount Plate Belt Cover Traction BeltImpeller Belt 196753X421 Repair Parts Snow Thrower Model PP11530ES WheelsWheel Assembly LH 196752X421Clutch Slide CoverWheel Driver Retainer Ring Wheel LobeShear Bolt KIT Repair Parts Snow Thrower Model PP11530ES BAG of PartsSafety Ignition KEY WrenchRepair Parts Snow Thrower Model PP11530ES Decals Limited Warranty

96192001904, 421895 specifications

The Poulan 421895,96192001904 is a powerful chainsaw designed for both residential and professional use. Known for its robust construction and cutting efficiency, this model is widely recognized among tree care professionals and homeowners. It provides an ideal balance of power, ease of use, and durability, making it an essential tool for various cutting tasks, from trimming branches to felling trees.

One of the main features of the Poulan 421895 is its engine performance. It typically comes equipped with a reliable two-stroke engine that delivers impressive horsepower, ensuring efficient cutting capability for a variety of applications. The engine is designed for easy starting, which minimizes user frustration and enhances productivity. Additionally, the engine is built with lower emissions technology, aligning with environmental standards while reducing the carbon footprint.

The design of the Poulan 421895 includes an ergonomic handle that increases comfort during extended use. This feature is particularly beneficial for professionals who may spend long hours operating the tool. The chainsaw also includes anti-vibration technology, which helps reduce fatigue and improve control, making it easier to maneuver during cutting tasks.

Safety is a paramount concern in chainsaw operation, and the Poulan 421895 addresses this through several built-in safety features. It is equipped with a chain brake that stops the chain quickly in case of kickback, providing an added layer of protection for the user. Furthermore, the chainsaw incorporates a safety lock that prevents accidental starting, ensuring that users can operate the tool with peace of mind.

User maintenance is also a key focus of the Poulan 421895. The chainsaw features an automatic oiling system that keeps the chain lubricated during operation, prolonging the life of both the chain and the guide bar. This system reduces the need for frequent manual maintenance, allowing users to focus more on their work rather than upkeep.

In conclusion, the Poulan 421895,96192001904 is a versatile and efficient chainsaw that meets the needs of various users, from weekend warriors to seasoned professionals. With its powerful engine, ergonomic design, safety features, and low maintenance requirements, it stands out as a reliable choice for anyone in need of a dependable cutting tool. Whether tackling yard work or larger tree care projects, this chainsaw is built to deliver consistent performance.
Top Page Image Contents