Poulan 96192001904, 421895 owner manual Storage, Other

Page 18

SERVICE AND ADJUSTMENTS

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

AXLE

WHEEL

WHEEL HUB

FIG. 25

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 2,134 meters. If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a service centre/department.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a service centre/depart- ment, which has the proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex-

18 haust area is still warm.

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Chute Deflector Remote Control Parts Packed Separately in CartonRemove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineDrive speed control lever used to select forward or HOW to USE Your Snow Thrower StoppingTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig ADD Gasoline See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See FigStorage OtherTroubleshooting Scrapper BAR Auger HousingKEY Part Description Auger BearingSkid Plate LH Auger Assembly 30 LHAuger Assembly 30 RH Skid Plate RHExploded Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller PulleyPlastic Washer Weight BAR181160X479 Drift Cutter BAR WasherDeflector Weldment Deflector Control AssemblyChute Weldment Deflector SealKEY Part Repair Parts Snow Thrower Model PP11530ES Handles Lower Tube Loop Handle LHLoop Handle RH Pivot SupportKnob RED Repair PartsSpacer Handle KnobCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Drive Axle ShaftSprocket Repair Parts Snow Thrower Model PP11530ES Drive END Plate Speed Selector AssemblyDrive Plate Assembly Bottom PANENGINE, TEC FrameEngine Mount Plate Belt Cover Traction BeltImpeller Belt 196752X421 Repair Parts Snow Thrower Model PP11530ES WheelsWheel Assembly LH 196753X421Wheel Lobe CoverWheel Driver Retainer Ring Clutch SlideWrench Repair Parts Snow Thrower Model PP11530ES BAG of PartsSafety Ignition KEY Shear Bolt KITRepair Parts Snow Thrower Model PP11530ES Decals Limited Warranty

96192001904, 421895 specifications

The Poulan 421895,96192001904 is a powerful chainsaw designed for both residential and professional use. Known for its robust construction and cutting efficiency, this model is widely recognized among tree care professionals and homeowners. It provides an ideal balance of power, ease of use, and durability, making it an essential tool for various cutting tasks, from trimming branches to felling trees.

One of the main features of the Poulan 421895 is its engine performance. It typically comes equipped with a reliable two-stroke engine that delivers impressive horsepower, ensuring efficient cutting capability for a variety of applications. The engine is designed for easy starting, which minimizes user frustration and enhances productivity. Additionally, the engine is built with lower emissions technology, aligning with environmental standards while reducing the carbon footprint.

The design of the Poulan 421895 includes an ergonomic handle that increases comfort during extended use. This feature is particularly beneficial for professionals who may spend long hours operating the tool. The chainsaw also includes anti-vibration technology, which helps reduce fatigue and improve control, making it easier to maneuver during cutting tasks.

Safety is a paramount concern in chainsaw operation, and the Poulan 421895 addresses this through several built-in safety features. It is equipped with a chain brake that stops the chain quickly in case of kickback, providing an added layer of protection for the user. Furthermore, the chainsaw incorporates a safety lock that prevents accidental starting, ensuring that users can operate the tool with peace of mind.

User maintenance is also a key focus of the Poulan 421895. The chainsaw features an automatic oiling system that keeps the chain lubricated during operation, prolonging the life of both the chain and the guide bar. This system reduces the need for frequent manual maintenance, allowing users to focus more on their work rather than upkeep.

In conclusion, the Poulan 421895,96192001904 is a versatile and efficient chainsaw that meets the needs of various users, from weekend warriors to seasoned professionals. With its powerful engine, ergonomic design, safety features, and low maintenance requirements, it stands out as a reliable choice for anyone in need of a dependable cutting tool. Whether tackling yard work or larger tree care projects, this chainsaw is built to deliver consistent performance.
Top Page Image Contents