Poulan 421895, 96192001904 owner manual To Replace Belts See Fig, To Remove Wheels See Fig

Page 17

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 24)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a service centre/department.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construc- tion and should be replaced by original equipment manu- facturer (OEM) belts available from your nearest service centre/department. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/ or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding the auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE HAIRPIN FROM CLUTCH ROD and re- move clutch rod from swing plate. Tip swing plate forward.

7.REMOVE AUGER BELT from around pulley.

8.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around

pulleys.17

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

9.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

10.Install clutch rod in swing plate; secure with hairpin.

11.Place auger belt around and inside the groove of auger pulley only.

12.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

13.Move idler arm so it does not hit impeller pulley as you bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 12. Belt must be fully seated in pulley groove when bringing the snow thrower together.

14.Install the two (2) hex bolts and tighten securely.

15.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, lockwasher and bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

16.INSTALL BELT COVER and two (2) screws. Tighten securely.

17.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

TRACTION DRIVE BELT

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

LOCKWASHER

 

 

BOLT

IDLER ARM

AUGER

SQUARE

BELT

HOLE

 

 

CLUTCHING

 

 

IDLER ARM

 

 

BRACKET

 

FRAME

AUGER PULLEY

AUGER

HOUSING

 

 

 

BOLTS

FIG. 24

TO REMOVE WHEELS (See Fig. 25)

•Remove the klik pin and remove wheel from axle.

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Chute Deflector Remote ControlHOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEYDrive speed control lever used to select forward or Meets A.N.S.I. Safety RequirementsRecoil auxiliary starter handle used for starting engine Stopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Throw Snow See FigScraper BAR See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Remove Wheels See Fig To Replace Belts See FigOther StorageTroubleshooting KEY Part Description Auger HousingScrapper BAR Auger BearingAuger Assembly 30 RH Auger Assembly 30 LHSkid Plate LH Skid Plate RHExploded 178675X008 Corner Bracket Clean OUT Tool Gearbox AssemblyBearing Impeller Pulley181160X479 Drift Cutter BAR Weight BARPlastic Washer WasherChute Weldment Deflector Control AssemblyDeflector Weldment Deflector SealKEY Part Repair Parts Snow Thrower Model PP11530ES Handles Loop Handle RH Loop Handle LHLower Tube Pivot SupportSpacer Repair PartsKnob RED Handle KnobCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Sprocket DriveAxle Shaft Repair Parts Snow Thrower Model PP11530ES Drive Drive Plate Assembly Speed Selector AssemblyEND Plate Bottom PANEngine Mount Plate ENGINE, TECFrame Impeller Belt Belt CoverTraction Belt Wheel Assembly LH Repair Parts Snow Thrower Model PP11530ES Wheels196752X421 196753X421Wheel Driver Retainer Ring CoverWheel Lobe Clutch SlideSafety Ignition KEY Repair Parts Snow Thrower Model PP11530ES BAG of PartsWrench Shear Bolt KITRepair Parts Snow Thrower Model PP11530ES Decals Limited Warranty

96192001904, 421895 specifications

The Poulan 421895,96192001904 is a powerful chainsaw designed for both residential and professional use. Known for its robust construction and cutting efficiency, this model is widely recognized among tree care professionals and homeowners. It provides an ideal balance of power, ease of use, and durability, making it an essential tool for various cutting tasks, from trimming branches to felling trees.

One of the main features of the Poulan 421895 is its engine performance. It typically comes equipped with a reliable two-stroke engine that delivers impressive horsepower, ensuring efficient cutting capability for a variety of applications. The engine is designed for easy starting, which minimizes user frustration and enhances productivity. Additionally, the engine is built with lower emissions technology, aligning with environmental standards while reducing the carbon footprint.

The design of the Poulan 421895 includes an ergonomic handle that increases comfort during extended use. This feature is particularly beneficial for professionals who may spend long hours operating the tool. The chainsaw also includes anti-vibration technology, which helps reduce fatigue and improve control, making it easier to maneuver during cutting tasks.

Safety is a paramount concern in chainsaw operation, and the Poulan 421895 addresses this through several built-in safety features. It is equipped with a chain brake that stops the chain quickly in case of kickback, providing an added layer of protection for the user. Furthermore, the chainsaw incorporates a safety lock that prevents accidental starting, ensuring that users can operate the tool with peace of mind.

User maintenance is also a key focus of the Poulan 421895. The chainsaw features an automatic oiling system that keeps the chain lubricated during operation, prolonging the life of both the chain and the guide bar. This system reduces the need for frequent manual maintenance, allowing users to focus more on their work rather than upkeep.

In conclusion, the Poulan 421895,96192001904 is a versatile and efficient chainsaw that meets the needs of various users, from weekend warriors to seasoned professionals. With its powerful engine, ergonomic design, safety features, and low maintenance requirements, it stands out as a reliable choice for anyone in need of a dependable cutting tool. Whether tackling yard work or larger tree care projects, this chainsaw is built to deliver consistent performance.
Top Page Image Contents