Poulan 96192001803 owner manual Engine, Cleaning

Page 15

MAINTENANCE

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigADD Gasoline See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningService and Adjustments To Adjust Snow Thrower HeightChute Deflector To Remove Wheels See Fig Other StorageTroubleshooting 1958 405972X479 405973X479Page 414280 Knob, Lever Repair Parts Snow Thrower Model PP10530ES Handles Repair Parts Snow Thrower Model PP10530ES Handles Repair Parts Snow Thrower Model PP10530ES Drive 751153 Nut, Lock 5/16-18   414999X428 KEY Part Description181044 179354Snow Thrower Model PP10530ES 185602X004 185603X479418974 418975 Limited Warranty

96192001803 specifications

The Poulan 96192001803 is a powerful and versatile chainsaw that caters to both casual users and professional arborists alike. With its robust design and advanced features, it stands out as a reliable option for those in need of a dependable tool for cutting, trimming, and maintaining their outdoor spaces.

At the core of the Poulan 96192001803 is its high-performance engine. It boasts a 50cc 2-stroke engine that delivers ample power for tackling a wide range of cutting tasks. This engine is designed for both efficiency and performance, ensuring that users can achieve clean cuts in a variety of materials, from softwoods to hardwoods. The chainsaw features a chain speed of up to 9,000 RPM, enabling quick and efficient cutting.

One notable feature of the Poulan 96192001803 is its ergonomic design. The chainsaw is equipped with a padded handle that provides a comfortable grip, reducing fatigue during extended use. The lightweight construction of the chainsaw further enhances user comfort, allowing for better maneuverability and control, which is crucial for precision cutting.

Technology plays a key role in the performance of the Poulan chainsaw. It incorporates an air-injection system that helps to keep the air filter clean, thus extending the life of the engine. This system ensures that users spend less time on maintenance and more time getting the job done. Additionally, the chainsaw includes a tool-less chain tensioning system, making it easy to adjust the chain to the desired tightness without the need for additional tools.

Safety is a top priority in the design of the Poulan 96192001803. Thechainsaw comes equipped with a chain brake that can quickly stop the chain in the event of kickback, providing an added layer of protection for the user. Moreover, the front and rear hand guards help prevent accidental contact with the chain, further enhancing safety during operation.

In terms of characteristics, the Poulan 96192001803 features a 20-inch bar length, making it suitable for a variety of cutting applications, from felling small trees to pruning larger branches. The chainsaw is compatible with a wide range of chains and bars, allowing users to customize their tool based on specific needs.

Overall, the Poulan 96192001803 is a well-rounded chainsaw that combines power, comfort, and safety features in one package. With its efficient engine, innovative technologies, and user-friendly design, it is an excellent choice for anyone looking to take on outdoor cutting tasks with ease and confidence. Whether for home use or professional jobs, this chainsaw is equipped to handle the demands of various cutting jobs, making it a valuable addition to any tool collection.
Top Page Image Contents