Poulan 96192001803 owner manual Table of Contents

Page 3

6.When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impel- ler and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the engine.

7.Do not run the engine indoors, except when starting the engine and for transporting the snow thrower in or out of the building. Open the outside doors; exhaust fumes are dangerous.

8.Exercise extreme caution when operating on slopes.

9.Never operate the snow thrower without proper guards, and other safety protective devices in place and work- ing.

10.Never direct the discharge toward people or areas where property damage can occur. Keep children and others away.

11.Do not overload the machine capacity by attempting to clear snow at too fast a rate.

12.Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when operating in reverse.

13.Disengage power to the collector/impeller when snow thrower is transported or not in use.

14.Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counterweights, or cabs).

15.Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run.

16. Never touch a hot engine or muffler.

Clearing a Clogged Discharge Chute

Hand contact with the rotating impeller inside the discharge chute is the most common cause of injury associated with snow throwers. Never use your hand to clean out the dis- charge chute. To clear the chute:

1.SHUT THE ENGINE OFF!

2.Wait 10 seconds to be sure the impeller blades have stopped rotating.

3.Always use a clean-out tool, not your hands.

Maintenance and Storage

1.Check shear bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

2.Never store the machine with fuel in the fuel tank inside a building where ignition sources are present such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing in any enclosure.

3.Always refer to operator’s manual for important details if the snow thrower is to be stored for an extended period.

4.Maintain or replace safety and instruction labels, as necessary.

5.Run the machine a few minutes after throwing snow to prevent freeze-up of the collector/impeller.

CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and manufac- tured to give best possible dependability and performance.

Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. We have competent, well-trained technicians and the proper tools to service or repair this unit.

Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower properly. Always observe the “SAFETY RULES”.

SERIAL NUMBER: ___________________________

DATE OF PURCHASE: _______________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A DECAL ATTACHED TO THE REAR OF THE SNOW THROWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

PRODUCT SPECIFICATIONS

Gasoline Capacity

4.0 Quarts

and Type:

 

Unleaded Regular only

 

 

Oil Type

SAE 30 (above 40°F)

(API SG–SL):

SAE 5W-30 or 10W-30 (0° to +40°F)

 

SAE 0W-30 (below 0°F)

 

 

Oil Capacity:

26 Ounces (0,74 Liters)

 

 

Spark Plug:

Champion RJ19LM

Gap:

0.030" (0,762 mm)

 

 

 

CUSTOMER RESPONSIBILITIES

•Read and observe the safety rules.

•Follow a regular schedule in maintaining, caring for and using your snow thrower.

•Follow the instructions under “Maintenance” and “Stor- age” sections of this owner’s manual.

TABLE OF CONTENTS

SAFETY RULES

2-3

PRODUCT SPECIFICATIONS

3

CUSTOMER RESPONSIBILITIES

3

ASSEMBLY / PRE-OPERATION

4-6

OPERATION

8-13

MAINTENANCE

14-15

MAINTENANCE SCHEDULE

14

SERVICE AND ADJUSTMENTS

16-18

STORAGE

18

TROUBLESHOOTING

19

REPAIR PARTS

20-31

3 WARRANTY

32

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigADD Gasoline See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningService and Adjustments To Adjust Snow Thrower HeightChute Deflector To Remove Wheels See Fig Other StorageTroubleshooting 1958 405972X479 405973X479Page 414280 Knob, Lever Repair Parts Snow Thrower Model PP10530ES Handles Repair Parts Snow Thrower Model PP10530ES Handles Repair Parts Snow Thrower Model PP10530ES Drive 751153 Nut, Lock 5/16-18   414999X428 KEY Part Description181044 179354Snow Thrower Model PP10530ES 185602X004 185603X479418974 418975 Limited Warranty

96192001803 specifications

The Poulan 96192001803 is a powerful and versatile chainsaw that caters to both casual users and professional arborists alike. With its robust design and advanced features, it stands out as a reliable option for those in need of a dependable tool for cutting, trimming, and maintaining their outdoor spaces.

At the core of the Poulan 96192001803 is its high-performance engine. It boasts a 50cc 2-stroke engine that delivers ample power for tackling a wide range of cutting tasks. This engine is designed for both efficiency and performance, ensuring that users can achieve clean cuts in a variety of materials, from softwoods to hardwoods. The chainsaw features a chain speed of up to 9,000 RPM, enabling quick and efficient cutting.

One notable feature of the Poulan 96192001803 is its ergonomic design. The chainsaw is equipped with a padded handle that provides a comfortable grip, reducing fatigue during extended use. The lightweight construction of the chainsaw further enhances user comfort, allowing for better maneuverability and control, which is crucial for precision cutting.

Technology plays a key role in the performance of the Poulan chainsaw. It incorporates an air-injection system that helps to keep the air filter clean, thus extending the life of the engine. This system ensures that users spend less time on maintenance and more time getting the job done. Additionally, the chainsaw includes a tool-less chain tensioning system, making it easy to adjust the chain to the desired tightness without the need for additional tools.

Safety is a top priority in the design of the Poulan 96192001803. Thechainsaw comes equipped with a chain brake that can quickly stop the chain in the event of kickback, providing an added layer of protection for the user. Moreover, the front and rear hand guards help prevent accidental contact with the chain, further enhancing safety during operation.

In terms of characteristics, the Poulan 96192001803 features a 20-inch bar length, making it suitable for a variety of cutting applications, from felling small trees to pruning larger branches. The chainsaw is compatible with a wide range of chains and bars, allowing users to customize their tool based on specific needs.

Overall, the Poulan 96192001803 is a well-rounded chainsaw that combines power, comfort, and safety features in one package. With its efficient engine, innovative technologies, and user-friendly design, it is an excellent choice for anyone looking to take on outdoor cutting tasks with ease and confidence. Whether for home use or professional jobs, this chainsaw is equipped to handle the demands of various cutting jobs, making it a valuable addition to any tool collection.
Top Page Image Contents