Poulan 96192001803 owner manual Safe Operation Practices for Walk-Behind Snow Throwers

Page 2

IMPORTANT

Safe Operation Practices for Walk-Behind Snow Throwers

This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury.

Look for this symbol to point out im- portant safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.

WARNING: Always remove safety igni- tion key and disconnect spark plug wire and place it where it cannot contact plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs.

WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be exercised while using on sloping sur- faces. Do not use snow thrower on surfaces above ground level such as roofs of residences, garages, porches or other such structures or buildings.

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

CAUTION: Muffler and other engine parts become extremely hot during operation and remain hot after engine has stopped. To avoid severe burns on contact, stay away from these areas.

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemi- cals known to the State of California to cause cancer and birth defects or other reproductive harm.

Training

1.Read, understand and follow all instructions on the machine and in the manual(s) before operating this unit. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly.

2.Never allow children to operate the equipment. Never allow adults to operate the equipment without proper instruction.

3.Keep the area of operation clear of all persons, par- ticularly small children.

4.Exercise caution to avoid slipping or falling, especially when operating the snow thrower in reverse.

Preparation

1.Thoroughly inspect the area where the equipment is to be used and remove all doormats, sleds, boards, wires, and other foreign objects.

2.Disengage all clutches and shift into neutral before starting the engine (motor).

3.Do not operate the equipment without wearing adequate winter garments. Avoid loose fitting clothing that can get caught in moving parts. Wear footwear that will improve footing on slippery surfaces.

4.Handle fuel with care; it is highly flammable

(a)Use an approved fuel container.

(b)Never add fuel to a running engine or hot en- gine.

(c)Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.

(d)Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground, away from your vehicle, before filling.

(e)When practical, remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle.

(f)Keep the nozzle in contact with the rim of the fuel tank or container opening at all times, until refuel- ing is complete. Do not use a nozzle lock-open device.

(g)Replace gasoline cap securely and wipe up spilled fuel.

(h)If fuel is spilled on clothing, change clothing im- mediately.

5.Use extension cords and receptacles as specified by the manufacturer for all units with electric drive motors or electric starting motors.

6.Adjust the collector housing height to clear gravel or crushed rock surface.

7.Never attempt to make any adjustments while the engine (motor) is running (except when specifically recommended by manufacturer).

8.Always wear safety glasses or eye shields during op- eration or while performing an adjustment or repair to protect eyes from foreign objects that may be thrown from the machine.

Operation

1.Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.

2.Exercise extreme caution when operating on or cross- ing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

3.After striking a foreign object, stop the engine (motor), remove the wire from the spark plug, disconnect the cord on electric motors, thoroughly inspect the snow thrower for any damage, and repair the damage before restarting and operating the snow thrower.

4.If the unit should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble.

5.Stop the engine (motor) whenever you leave the oper- ating position, before unclogging the collector/impeller housing or discharge chute, and when making any

2

repairs, adjustments or inspections.

 

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigCheck Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine ADD Gasoline See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Storage OtherTroubleshooting 1958 405973X479 405972X479Page 414280 Knob, Lever Repair Parts Snow Thrower Model PP10530ES Handles Repair Parts Snow Thrower Model PP10530ES Handles Repair Parts Snow Thrower Model PP10530ES Drive 751153 Nut, Lock 5/16-18   179354 KEY Part Description181044 414999X428Snow Thrower Model PP10530ES 418974 418975 185602X004185603X479 Limited Warranty

96192001803 specifications

The Poulan 96192001803 is a powerful and versatile chainsaw that caters to both casual users and professional arborists alike. With its robust design and advanced features, it stands out as a reliable option for those in need of a dependable tool for cutting, trimming, and maintaining their outdoor spaces.

At the core of the Poulan 96192001803 is its high-performance engine. It boasts a 50cc 2-stroke engine that delivers ample power for tackling a wide range of cutting tasks. This engine is designed for both efficiency and performance, ensuring that users can achieve clean cuts in a variety of materials, from softwoods to hardwoods. The chainsaw features a chain speed of up to 9,000 RPM, enabling quick and efficient cutting.

One notable feature of the Poulan 96192001803 is its ergonomic design. The chainsaw is equipped with a padded handle that provides a comfortable grip, reducing fatigue during extended use. The lightweight construction of the chainsaw further enhances user comfort, allowing for better maneuverability and control, which is crucial for precision cutting.

Technology plays a key role in the performance of the Poulan chainsaw. It incorporates an air-injection system that helps to keep the air filter clean, thus extending the life of the engine. This system ensures that users spend less time on maintenance and more time getting the job done. Additionally, the chainsaw includes a tool-less chain tensioning system, making it easy to adjust the chain to the desired tightness without the need for additional tools.

Safety is a top priority in the design of the Poulan 96192001803. Thechainsaw comes equipped with a chain brake that can quickly stop the chain in the event of kickback, providing an added layer of protection for the user. Moreover, the front and rear hand guards help prevent accidental contact with the chain, further enhancing safety during operation.

In terms of characteristics, the Poulan 96192001803 features a 20-inch bar length, making it suitable for a variety of cutting applications, from felling small trees to pruning larger branches. The chainsaw is compatible with a wide range of chains and bars, allowing users to customize their tool based on specific needs.

Overall, the Poulan 96192001803 is a well-rounded chainsaw that combines power, comfort, and safety features in one package. With its efficient engine, innovative technologies, and user-friendly design, it is an excellent choice for anyone looking to take on outdoor cutting tasks with ease and confidence. Whether for home use or professional jobs, this chainsaw is equipped to handle the demands of various cutting jobs, making it a valuable addition to any tool collection.
Top Page Image Contents