Poulan 96192001803 owner manual To Remove Wheels See Fig

Page 17

SERVICE AND ADJUSTMENTS

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts and lock washers holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE AUGER BELT from around pulley.

7.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 10. Belt must be fully seated in pulley groove when bringing the snow thrower together.

12.Install the two (2) hex bolts and lock washers and tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, lockwasher and bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

TRACTION DRIVE BELT

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

LOCKWASHER

 

 

BOLT

IDLER ARM

 

AUGER

SQUARE

 

BELT

HOLE

 

 

CLUTCHING

 

IDLER ARM

 

BRACKET

 

 

AUGER PULLEY

 

 

 

BOLT

FRAME

AUGER

 

HOUSING

 

FIG. 22

TO REMOVE WHEELS (See Fig. 23)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Other StorageTroubleshooting 1958 405972X479 405973X479Page 414280 Knob, Lever Repair Parts Snow Thrower Model PP10530ES Handles Repair Parts Snow Thrower Model PP10530ES Handles Repair Parts Snow Thrower Model PP10530ES Drive 751153 Nut, Lock 5/16-18   181044 KEY Part Description179354 414999X428Snow Thrower Model PP10530ES 418974 418975 185602X004185603X479 Limited Warranty

96192001803 specifications

The Poulan 96192001803 is a powerful and versatile chainsaw that caters to both casual users and professional arborists alike. With its robust design and advanced features, it stands out as a reliable option for those in need of a dependable tool for cutting, trimming, and maintaining their outdoor spaces.

At the core of the Poulan 96192001803 is its high-performance engine. It boasts a 50cc 2-stroke engine that delivers ample power for tackling a wide range of cutting tasks. This engine is designed for both efficiency and performance, ensuring that users can achieve clean cuts in a variety of materials, from softwoods to hardwoods. The chainsaw features a chain speed of up to 9,000 RPM, enabling quick and efficient cutting.

One notable feature of the Poulan 96192001803 is its ergonomic design. The chainsaw is equipped with a padded handle that provides a comfortable grip, reducing fatigue during extended use. The lightweight construction of the chainsaw further enhances user comfort, allowing for better maneuverability and control, which is crucial for precision cutting.

Technology plays a key role in the performance of the Poulan chainsaw. It incorporates an air-injection system that helps to keep the air filter clean, thus extending the life of the engine. This system ensures that users spend less time on maintenance and more time getting the job done. Additionally, the chainsaw includes a tool-less chain tensioning system, making it easy to adjust the chain to the desired tightness without the need for additional tools.

Safety is a top priority in the design of the Poulan 96192001803. Thechainsaw comes equipped with a chain brake that can quickly stop the chain in the event of kickback, providing an added layer of protection for the user. Moreover, the front and rear hand guards help prevent accidental contact with the chain, further enhancing safety during operation.

In terms of characteristics, the Poulan 96192001803 features a 20-inch bar length, making it suitable for a variety of cutting applications, from felling small trees to pruning larger branches. The chainsaw is compatible with a wide range of chains and bars, allowing users to customize their tool based on specific needs.

Overall, the Poulan 96192001803 is a well-rounded chainsaw that combines power, comfort, and safety features in one package. With its efficient engine, innovative technologies, and user-friendly design, it is an excellent choice for anyone looking to take on outdoor cutting tasks with ease and confidence. Whether for home use or professional jobs, this chainsaw is equipped to handle the demands of various cutting jobs, making it a valuable addition to any tool collection.
Top Page Image Contents