Poulan 96192001803 owner manual Storage, Other

Page 18

SERVICE AND ADJUSTMENTS

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 23

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex- haust area is still warm.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigCheck Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine ADD Gasoline See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector To Remove Wheels See Fig Storage OtherTroubleshooting 1958 405973X479 405972X479Page 414280 Knob, Lever Repair Parts Snow Thrower Model PP10530ES Handles Repair Parts Snow Thrower Model PP10530ES Handles Repair Parts Snow Thrower Model PP10530ES Drive 751153 Nut, Lock 5/16-18   179354 KEY Part Description181044 414999X428Snow Thrower Model PP10530ES 185602X004 185603X479418974 418975 Limited Warranty

96192001803 specifications

The Poulan 96192001803 is a powerful and versatile chainsaw that caters to both casual users and professional arborists alike. With its robust design and advanced features, it stands out as a reliable option for those in need of a dependable tool for cutting, trimming, and maintaining their outdoor spaces.

At the core of the Poulan 96192001803 is its high-performance engine. It boasts a 50cc 2-stroke engine that delivers ample power for tackling a wide range of cutting tasks. This engine is designed for both efficiency and performance, ensuring that users can achieve clean cuts in a variety of materials, from softwoods to hardwoods. The chainsaw features a chain speed of up to 9,000 RPM, enabling quick and efficient cutting.

One notable feature of the Poulan 96192001803 is its ergonomic design. The chainsaw is equipped with a padded handle that provides a comfortable grip, reducing fatigue during extended use. The lightweight construction of the chainsaw further enhances user comfort, allowing for better maneuverability and control, which is crucial for precision cutting.

Technology plays a key role in the performance of the Poulan chainsaw. It incorporates an air-injection system that helps to keep the air filter clean, thus extending the life of the engine. This system ensures that users spend less time on maintenance and more time getting the job done. Additionally, the chainsaw includes a tool-less chain tensioning system, making it easy to adjust the chain to the desired tightness without the need for additional tools.

Safety is a top priority in the design of the Poulan 96192001803. Thechainsaw comes equipped with a chain brake that can quickly stop the chain in the event of kickback, providing an added layer of protection for the user. Moreover, the front and rear hand guards help prevent accidental contact with the chain, further enhancing safety during operation.

In terms of characteristics, the Poulan 96192001803 features a 20-inch bar length, making it suitable for a variety of cutting applications, from felling small trees to pruning larger branches. The chainsaw is compatible with a wide range of chains and bars, allowing users to customize their tool based on specific needs.

Overall, the Poulan 96192001803 is a well-rounded chainsaw that combines power, comfort, and safety features in one package. With its efficient engine, innovative technologies, and user-friendly design, it is an excellent choice for anyone looking to take on outdoor cutting tasks with ease and confidence. Whether for home use or professional jobs, this chainsaw is equipped to handle the demands of various cutting jobs, making it a valuable addition to any tool collection.
Top Page Image Contents