Poulan 96192003503, 437970 owner manual Snow Throwing Tips, To Start Engine, Before Stopping

Page 13

OPERATION

TO START ENGINE

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

•Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Seri- ous personal injury or damage to your snow thrower could result.

COLD START - ELECTRIC STARTER

1.Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place ON / OFF switch in “ON” position.

3.Rotate choke control to “FULL” position.

4.Connect the power cord to the engine.

5.Plug the other end of the power cord into a three-hole grounded 120 Volt A.C. receptacle.

NOTE: Do not use primer when starting engine with the electric starter.

6. Push starter button until engine starts.

IMPORTANT: Do not crank engine more than five continu- ous seconds between each time you try to start. Wait 5 to 10 seconds between each attempt.

7.When the engine starts, release the starter button and slowly move the choke control to the “OFF” position.

8.Disconnect the power cord from the receptacle first, then from the engine.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - ELECTRIC STARTER

Follow the steps above, keeping the choke control in the “OFF” position.

COLD START - RECOIL STARTER

1.Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place ON / OFF switch in “ON” position.

3.Rotate choke control to “FULL” position.

4.Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. If temperature is above 50°F, priming is not necessary.

NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer.

5.Pull recoil starter handle quickly. Do not allow starter rope to snap back.

6.When the engine starts, release the recoil starter handle and slowly move the choke control to the “OFF” posi- tion.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - RECOIL STARTER

Follow the steps above, keeping the choke in the “OFF” position. DO NOT push the primer.

BEFORE STOPPING

Run the engine for a few minutes to help dry off any mois- ture on the engine.

IF RECOIL STARTER HAS FROZEN

If the recoil starter has frozen and will not turn the engine, proceed as follows:

1.Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible.

2.Release the recoil starter handle and let it snap back against the starter.

If the engine still fails to start, repeat the above steps or use the electric starter.

SNOW THROWING TIPS

•Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the ON / OFF switch, to adjust speed.

•It is easier and more efficient to remove snow imme- diately after it falls.

•The best time to remove snow is the early morning. At this time the snow is usually dry and has not been ex- posed to the direct sun and warming temperatures.

•Slightly overlap each successive path to ensure all snow will be removed.

•Throw snow downwind whenever possible.

•Adjust the skid plates to proper height for current snow conditions. See “TO ADJUST SKID PLATES” in this section of this manual.

•For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly.

•Keep engine clean and clear of snow during use. This will help air flow and extend engine life.

•After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine.

•Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use.

WARNING: Do not operate snow thrower if weather conditions impair visibility. Throwing snow during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the snow thrower.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo USE Choke Control See Fig To Control Snow Discharge See FigPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting Service Notes Exploded Tool Clip KEY Part DescriptionScrapper BAR Auger HousingCARRIAGEBOLT5/16−18X.625 Auger 30 LHBearing Plug Auger BearingSkid Plate LH Skid Plate RHChute Weldment Deflector Control AssemblyDeflector Weldment Deflector SealCable Assembly Adjustable LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketLoop Handle LH Repair Parts Snow Thrower Model XT11530ES HandlesLoop Handle RH Lower HandleImpeller ROD 180480Traction ROD RetainerSpacer Repair PartsKnob RED Handle KnobInterlock Spring Wire HarnessInterlock CAM Torsion SpringRepair Parts Snow Thrower Model XT11530ES Drive Speed Selector Sprocket Axle ShaftThrust Washer BearingFrame Engine Model436146X505 Engine Mount Plate428684 KEY Repair Parts Snow Thrower Model XT11530ES WheelsPart Description 432337X428 Wheel Assembly LH432338X428 Safety Ignition KEY Repair Parts Snow Thrower Model XT11530ES BAG of Parts193071 KIT Harness Conn B&S 435840181037 Repair Parts Snow Thrower Model XT11530ES DecalsDECAL, Danger DECAL, DANGER, DeflectorService Notes Service Notes Limited Warranty

96192003503, 437970 specifications

The Poulan 437970, also known by its model number 96192003503, is a powerful chainsaw designed for both professional and residential use. This versatile tool is known for its reliability and performance, making it an ideal choice for homeowners and landscapers alike.

One of the standout features of the Poulan 437970 is its powerful engine. Equipped with a 42cc 2-stroke engine, this chainsaw offers ample power to tackle a variety of cutting tasks, from tree trimming to firewood preparation. The engine's ability to deliver high torque at both low and high RPMs makes it suitable for both precise cuts and heavy-duty work.

The Poulan 437970 features a 16-inch guide bar, providing a good balance between maneuverability and cutting capacity. This length is particularly useful for homeowners who need to handle branches or trees of moderate size. The chainsaw is designed with a low-profile chain that reduces kickback, enhancing safety during operation. This feature is essential for inexperienced users who might be more prone to mishaps.

In terms of technology, the Poulan 437970 incorporates an effortless start feature, which is a significant advantage for users who may struggle with traditional pull-start mechanisms. This technology helps to reduce the amount of effort required to start the chainsaw, making it more user-friendly and accessible.

Another notable characteristic of the Poulan 437970 is its automatic oiling system. This system ensures that the chain and bar receive a steady flow of lubrication during operation, which reduces friction and extends the life of the chainsaw. A well-lubricated chain also translates to smoother cuts and less wear and tear on the equipment.

The chainsaw also includes a safety throttle lockout feature, which prevents accidental engagement of the throttle, adding an extra layer of safety for users. This feature is particularly important for those who may be using the chainsaw for extended periods or in challenging conditions.

With its combination of power, safety features, and ease of use, the Poulan 437970,96192003503 stands out in the market as a reliable choice for both novice and experienced users. Whether you’re handling light landscaping tasks or more demanding cutting jobs, this chainsaw is designed to deliver optimal performance and durability. Overall, investing in the Poulan 437970 means you’re choosing a tool that promises efficiency and effectiveness no matter the job at hand.
Top Page Image Contents