Poulan 96192003503, 437970 owner manual Storage, Other, Fuel System, Engine OIL, Cylinder

Page 19

STORAGE

Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex- haust area is still warm.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo Control Snow Discharge See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Service Notes Exploded Tool Clip KEY Part DescriptionAuger 30 LH Auger HousingScrapper BAR CARRIAGEBOLT5/16−18X.625Skid Plate RH Auger BearingBearing Plug Skid Plate LHDeflector Seal Deflector Control AssemblyChute Weldment Deflector WeldmentRotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLower Handle Repair Parts Snow Thrower Model XT11530ES HandlesLoop Handle LH Loop Handle RHRetainer 180480Impeller ROD Traction RODHandle Knob Repair PartsSpacer Knob REDTorsion Spring Wire HarnessInterlock Spring Interlock CAMRepair Parts Snow Thrower Model XT11530ES Drive Speed Selector Bearing Axle ShaftSprocket Thrust WasherEngine Mount Plate Engine ModelFrame 436146X505428684 KEY Repair Parts Snow Thrower Model XT11530ES WheelsPart Description 432337X428 Wheel Assembly LH432338X428 Safety Ignition KEY Repair Parts Snow Thrower Model XT11530ES BAG of Parts193071 KIT Harness Conn B&S 435840DECAL, DANGER, Deflector Repair Parts Snow Thrower Model XT11530ES Decals181037 DECAL, DangerService Notes Service Notes Limited Warranty

96192003503, 437970 specifications

The Poulan 437970, also known by its model number 96192003503, is a powerful chainsaw designed for both professional and residential use. This versatile tool is known for its reliability and performance, making it an ideal choice for homeowners and landscapers alike.

One of the standout features of the Poulan 437970 is its powerful engine. Equipped with a 42cc 2-stroke engine, this chainsaw offers ample power to tackle a variety of cutting tasks, from tree trimming to firewood preparation. The engine's ability to deliver high torque at both low and high RPMs makes it suitable for both precise cuts and heavy-duty work.

The Poulan 437970 features a 16-inch guide bar, providing a good balance between maneuverability and cutting capacity. This length is particularly useful for homeowners who need to handle branches or trees of moderate size. The chainsaw is designed with a low-profile chain that reduces kickback, enhancing safety during operation. This feature is essential for inexperienced users who might be more prone to mishaps.

In terms of technology, the Poulan 437970 incorporates an effortless start feature, which is a significant advantage for users who may struggle with traditional pull-start mechanisms. This technology helps to reduce the amount of effort required to start the chainsaw, making it more user-friendly and accessible.

Another notable characteristic of the Poulan 437970 is its automatic oiling system. This system ensures that the chain and bar receive a steady flow of lubrication during operation, which reduces friction and extends the life of the chainsaw. A well-lubricated chain also translates to smoother cuts and less wear and tear on the equipment.

The chainsaw also includes a safety throttle lockout feature, which prevents accidental engagement of the throttle, adding an extra layer of safety for users. This feature is particularly important for those who may be using the chainsaw for extended periods or in challenging conditions.

With its combination of power, safety features, and ease of use, the Poulan 437970,96192003503 stands out in the market as a reliable choice for both novice and experienced users. Whether you’re handling light landscaping tasks or more demanding cutting jobs, this chainsaw is designed to deliver optimal performance and durability. Overall, investing in the Poulan 437970 means you’re choosing a tool that promises efficiency and effectiveness no matter the job at hand.
Top Page Image Contents