Poulan 96192003503, 437970 owner manual Engine, Cleaning

Page 15

MAINTENANCE

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klik pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo Control Snow Discharge See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Move Forward and Backward See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Service Notes Exploded Tool Clip KEY Part DescriptionAuger 30 LH Auger HousingScrapper BAR CARRIAGEBOLT5/16−18X.625Skid Plate RH Auger BearingBearing Plug Skid Plate LHDeflector Seal Deflector Control AssemblyChute Weldment Deflector WeldmentRotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLower Handle Repair Parts Snow Thrower Model XT11530ES HandlesLoop Handle LH Loop Handle RHRetainer 180480Impeller ROD Traction RODHandle Knob Repair PartsSpacer Knob REDTorsion Spring Wire HarnessInterlock Spring Interlock CAMRepair Parts Snow Thrower Model XT11530ES Drive Speed Selector Bearing Axle ShaftSprocket Thrust WasherEngine Mount Plate Engine ModelFrame 436146X505428684 Repair Parts Snow Thrower Model XT11530ES Wheels KEYPart Description Wheel Assembly LH 432337X428432338X428 Repair Parts Snow Thrower Model XT11530ES BAG of Parts Safety Ignition KEY193071 KIT Harness Conn B&S 435840DECAL, DANGER, Deflector Repair Parts Snow Thrower Model XT11530ES Decals181037 DECAL, DangerService Notes Service Notes Limited Warranty

96192003503, 437970 specifications

The Poulan 437970, also known by its model number 96192003503, is a powerful chainsaw designed for both professional and residential use. This versatile tool is known for its reliability and performance, making it an ideal choice for homeowners and landscapers alike.

One of the standout features of the Poulan 437970 is its powerful engine. Equipped with a 42cc 2-stroke engine, this chainsaw offers ample power to tackle a variety of cutting tasks, from tree trimming to firewood preparation. The engine's ability to deliver high torque at both low and high RPMs makes it suitable for both precise cuts and heavy-duty work.

The Poulan 437970 features a 16-inch guide bar, providing a good balance between maneuverability and cutting capacity. This length is particularly useful for homeowners who need to handle branches or trees of moderate size. The chainsaw is designed with a low-profile chain that reduces kickback, enhancing safety during operation. This feature is essential for inexperienced users who might be more prone to mishaps.

In terms of technology, the Poulan 437970 incorporates an effortless start feature, which is a significant advantage for users who may struggle with traditional pull-start mechanisms. This technology helps to reduce the amount of effort required to start the chainsaw, making it more user-friendly and accessible.

Another notable characteristic of the Poulan 437970 is its automatic oiling system. This system ensures that the chain and bar receive a steady flow of lubrication during operation, which reduces friction and extends the life of the chainsaw. A well-lubricated chain also translates to smoother cuts and less wear and tear on the equipment.

The chainsaw also includes a safety throttle lockout feature, which prevents accidental engagement of the throttle, adding an extra layer of safety for users. This feature is particularly important for those who may be using the chainsaw for extended periods or in challenging conditions.

With its combination of power, safety features, and ease of use, the Poulan 437970,96192003503 stands out in the market as a reliable choice for both novice and experienced users. Whether you’re handling light landscaping tasks or more demanding cutting jobs, this chainsaw is designed to deliver optimal performance and durability. Overall, investing in the Poulan 437970 means you’re choosing a tool that promises efficiency and effectiveness no matter the job at hand.
Top Page Image Contents