Poulan 96192003503, 437970 owner manual To Replace Belts See Fig

Page 17

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 21)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a service center/department.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construc- tion and should be replaced by original equipment manu- facturer (OEM) belts available from your nearest service center/department. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/ or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding the auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE HAIRPIN FROM CLUTCH ROD and re- move clutch rod from swing plate. Tip swing plate forward.

7.REMOVE AUGER BELT from around pulley.

8.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

9.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

10.Install clutch rod in swing plate; secure with hairpin.

11.Place auger belt around and inside the groove of auger pulley only.

12.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

13.Move idler arm so it does not hit impeller pulley as you bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 12. Belt must be fully seated in pulley groove when bringing the snow thrower together.

14.Install the two (2) hex bolts and tighten securely.

15.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

16.INSTALL BELT COVER and two (2) screws. Tighten securely.

17.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

 

TRACTION DRIVE BELT

 

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

 

BOLT

 

IDLER ARM

 

AUGER

SQUARE

 

BELT

HOLE

 

 

 

CLUTCHING

 

 

 

IDLER ARM

 

 

 

BRACKET

 

 

FRAME

AUGER PULLEY

AUGER

HOUSING

 

 

 

BOLTS

 

17

FIG. 21

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo USE Choke Control See Fig To Control Snow Discharge See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting Service Notes Exploded Tool Clip KEY Part DescriptionScrapper BAR Auger HousingCARRIAGEBOLT5/16−18X.625 Auger 30 LHBearing Plug Auger BearingSkid Plate LH Skid Plate RHChute Weldment Deflector Control AssemblyDeflector Weldment Deflector SealCable Assembly Adjustable LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketLoop Handle LH Repair Parts Snow Thrower Model XT11530ES HandlesLoop Handle RH Lower HandleImpeller ROD 180480Traction ROD RetainerSpacer Repair PartsKnob RED Handle KnobInterlock Spring Wire HarnessInterlock CAM Torsion SpringRepair Parts Snow Thrower Model XT11530ES Drive Speed Selector Sprocket Axle ShaftThrust Washer BearingFrame Engine Model436146X505 Engine Mount Plate428684 Part Description Repair Parts Snow Thrower Model XT11530ES WheelsKEY 432338X428 Wheel Assembly LH432337X428 193071 Repair Parts Snow Thrower Model XT11530ES BAG of PartsSafety Ignition KEY KIT Harness Conn B&S 435840181037 Repair Parts Snow Thrower Model XT11530ES DecalsDECAL, Danger DECAL, DANGER, DeflectorService Notes Service Notes Limited Warranty

96192003503, 437970 specifications

The Poulan 437970, also known by its model number 96192003503, is a powerful chainsaw designed for both professional and residential use. This versatile tool is known for its reliability and performance, making it an ideal choice for homeowners and landscapers alike.

One of the standout features of the Poulan 437970 is its powerful engine. Equipped with a 42cc 2-stroke engine, this chainsaw offers ample power to tackle a variety of cutting tasks, from tree trimming to firewood preparation. The engine's ability to deliver high torque at both low and high RPMs makes it suitable for both precise cuts and heavy-duty work.

The Poulan 437970 features a 16-inch guide bar, providing a good balance between maneuverability and cutting capacity. This length is particularly useful for homeowners who need to handle branches or trees of moderate size. The chainsaw is designed with a low-profile chain that reduces kickback, enhancing safety during operation. This feature is essential for inexperienced users who might be more prone to mishaps.

In terms of technology, the Poulan 437970 incorporates an effortless start feature, which is a significant advantage for users who may struggle with traditional pull-start mechanisms. This technology helps to reduce the amount of effort required to start the chainsaw, making it more user-friendly and accessible.

Another notable characteristic of the Poulan 437970 is its automatic oiling system. This system ensures that the chain and bar receive a steady flow of lubrication during operation, which reduces friction and extends the life of the chainsaw. A well-lubricated chain also translates to smoother cuts and less wear and tear on the equipment.

The chainsaw also includes a safety throttle lockout feature, which prevents accidental engagement of the throttle, adding an extra layer of safety for users. This feature is particularly important for those who may be using the chainsaw for extended periods or in challenging conditions.

With its combination of power, safety features, and ease of use, the Poulan 437970,96192003503 stands out in the market as a reliable choice for both novice and experienced users. Whether you’re handling light landscaping tasks or more demanding cutting jobs, this chainsaw is designed to deliver optimal performance and durability. Overall, investing in the Poulan 437970 means you’re choosing a tool that promises efficiency and effectiveness no matter the job at hand.
Top Page Image Contents