Poulan 437970 To Remove Wheels See Fig, To Adjust Cable Tension See Fig, Carburetor, Engine Speed

Page 18

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

AXLE

WHEEL

WHEEL HUB

FIG. 22

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

TO ADJUST CABLE TENSION (See Fig. 23)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 23

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See FigUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Service Notes Exploded KEY Part Description Tool ClipCARRIAGEBOLT5/16−18X.625 Auger HousingScrapper BAR Auger 30 LHSkid Plate LH Auger BearingBearing Plug Skid Plate RHDeflector Weldment Deflector Control AssemblyChute Weldment Deflector SealRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot BracketLoop Handle RH Repair Parts Snow Thrower Model XT11530ES HandlesLoop Handle LH Lower HandleTraction ROD 180480Impeller ROD RetainerKnob RED Repair PartsSpacer Handle KnobInterlock CAM Wire HarnessInterlock Spring Torsion SpringRepair Parts Snow Thrower Model XT11530ES Drive Speed Selector Thrust Washer Axle ShaftSprocket Bearing436146X505 Engine ModelFrame Engine Mount Plate428684 Repair Parts Snow Thrower Model XT11530ES Wheels KEYPart Description Wheel Assembly LH 432337X428432338X428 Repair Parts Snow Thrower Model XT11530ES BAG of Parts Safety Ignition KEY193071 435840 KIT Harness Conn B&SDECAL, Danger Repair Parts Snow Thrower Model XT11530ES Decals181037 DECAL, DANGER, DeflectorService Notes Service Notes Limited Warranty

96192003503, 437970 specifications

The Poulan 437970, also known by its model number 96192003503, is a powerful chainsaw designed for both professional and residential use. This versatile tool is known for its reliability and performance, making it an ideal choice for homeowners and landscapers alike.

One of the standout features of the Poulan 437970 is its powerful engine. Equipped with a 42cc 2-stroke engine, this chainsaw offers ample power to tackle a variety of cutting tasks, from tree trimming to firewood preparation. The engine's ability to deliver high torque at both low and high RPMs makes it suitable for both precise cuts and heavy-duty work.

The Poulan 437970 features a 16-inch guide bar, providing a good balance between maneuverability and cutting capacity. This length is particularly useful for homeowners who need to handle branches or trees of moderate size. The chainsaw is designed with a low-profile chain that reduces kickback, enhancing safety during operation. This feature is essential for inexperienced users who might be more prone to mishaps.

In terms of technology, the Poulan 437970 incorporates an effortless start feature, which is a significant advantage for users who may struggle with traditional pull-start mechanisms. This technology helps to reduce the amount of effort required to start the chainsaw, making it more user-friendly and accessible.

Another notable characteristic of the Poulan 437970 is its automatic oiling system. This system ensures that the chain and bar receive a steady flow of lubrication during operation, which reduces friction and extends the life of the chainsaw. A well-lubricated chain also translates to smoother cuts and less wear and tear on the equipment.

The chainsaw also includes a safety throttle lockout feature, which prevents accidental engagement of the throttle, adding an extra layer of safety for users. This feature is particularly important for those who may be using the chainsaw for extended periods or in challenging conditions.

With its combination of power, safety features, and ease of use, the Poulan 437970,96192003503 stands out in the market as a reliable choice for both novice and experienced users. Whether you’re handling light landscaping tasks or more demanding cutting jobs, this chainsaw is designed to deliver optimal performance and durability. Overall, investing in the Poulan 437970 means you’re choosing a tool that promises efficiency and effectiveness no matter the job at hand.
Top Page Image Contents