Poulan 96192003401, 429837 Maintenance, General Recommendations, Before Each USE, Lubrication

Page 13

MAINTENANCE

GENERAL RECOMMENDATIONS

LUBRICATION CHART

The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain snow thrower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your snow thrower.

At least once a season, check to see if you should make any of the adjustments described in the Service and Ad- justments section of this manual.

•At least once a year, you should replace the spark plug and check belts for wear. A new spark plug will help your engine run better and last longer.

•Follow the maintenance schedule in this manual.

NOTE: Use only Original Equipment Manufacturer (OEM) parts to service this unit. Failure to do so can cause the unit to malfunction and pose a risk of injury to the operator.

BEFORE EACH USE

1.Check engine oil level.

2.Check for loose fasteners.

3.Check controls to be sure they are functioning properly.

LUBRICATION

Keep your snow thrower well lubricated (See “LUBRICATION CHART”).

➀SAE 30 Motor Oil

➁ See “ENGINE” in

Maintenance section

➂ General

Purpose

Grease

➀ Pivot points

➁ Engine

➂ Auger

oil

grease fittings

SNOW THROWER

Always observe the safety rules when performing any maintenance.

TIRES

•Maintain proper air pressure in both tires (14–17 PSI).

•Keep tires free of gasoline and oil, which can harm rubber.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Install Speed Control ROD See Figs HOW to SET UP Your Snow ThrowerInstall Traction Drive Control ROD See Figs Tool BOX See FigInstall Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Know Your Snow Thrower OperationPrimer TractionRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo USE Choke Control See Fig To Control Snow Discharge See FigsTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigScraper BAR See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigBefore Stopping Snow Throwing TipsIf Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting 23 22 KEY Part Description Scraper BAR Auger HousingAuger 27 LH Auger 27 RHBearing Plug Auger BearingDeflector Weldment Chute WeldmentDeflector Seal StrapCable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator HeadLoop Handle RH Loop Handle LHLower Tube Pivot SupportRetainer SpacerKnob RED Handle KnobTraction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomConsole Panel Wire HarnessHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number XT827ES Drive Drive Plate Assembly Speed Selector AssemblyWheel HUB END PlateRoll PIN 3/16 Axle ShaftSprocket Clik PIN423185X505 FrameEngine Mounting Plate 428684Traction Belt Impeller BeltIdler ARM Bracket Idler Pulley187833X428 Wheel Assembly LH187865X428 193071 Safety Ignition KEYDECAL, Danger 181037DECAL, DANGER, Deflector Service Notes Service Notes Limited Warranty
Top Page Image Contents