Poulan 429837 Impeller Belt, Traction Belt, Idler ARM Bracket, Idler Pulley, Belt Guide

Page 34

REPAIR PARTS SNOW THROWER - - MODEL NUMBER XT827ES (96192003401)

CHASSIS / ENGINE / PULLEYS

23		22	14
24			14	21
24				21
				20
11
14	21		20	19
13			20	18
13				18
12				17
12	14			16
		15		16
		15		6
				6
	7
10
				5
8				4
8				3
				3
				9

1

2

01.21.003-B

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	408007	IMPELLER BELT
2	419744	TRACTION BELT
3	423723X479	IDLER ARM BRACKET
4	180523	IDLER PULLEY
5	426589	NUT 5/16-18

674780524 SCREW 5/16-18 X 1 .50

7423990X479 IDLER BRACKET

8	428867	SCREW 5/16-18 X .625
9	424297	SHOULDER BOLT 5/16-18 X .500

10751153 NUT 5/16-18 NYLOCK

11187786 TRACTION IDLER ARM

12180522 TRACTION PULLEY

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
13	74780520	SCREW 5/16-18 X 1 .00
14	59289	WASHER
15	73930500	NUT 5/16-18
16	851084	SCREW 3/8-24 X 1.375
17	400026	WASHER

18426491 PULLEY ENG IMPELLER

19426490 PULLEY ENG TRACTION

2074610516 SCREW 5/16-18 X 1 .00

2110040500 LOCKWASHER 5/16

22

155452

BELT GUIDE

2311050500 LOCKWASHER 5/16

24175331 IDLER BUSHING

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

34

Image 34

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Install Traction Drive Control ROD See Figs HOW to SET UP Your Snow ThrowerInstall Speed Control ROD See Figs Tool BOX See FigInstall Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower TractionMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See FigsTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig ADD Gasoline See FigBefore Stopping Snow Throwing TipsIf Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting 23 22 KEY Part Description Auger 27 LH Auger HousingScraper BAR Auger 27 RHAuger Bearing Bearing PlugDeflector Seal Chute WeldmentDeflector Weldment StrapCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLower Tube Loop Handle LHLoop Handle RH Pivot SupportKnob RED SpacerRetainer Handle KnobShifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD BottomHeadlight Bezel Wire HarnessConsole Panel Flood HeadlightRepair Parts Snow Thrower - Model Number XT827ES Drive Wheel HUB Speed Selector AssemblyDrive Plate Assembly END PlateSprocket Axle ShaftRoll PIN 3/16 Clik PINEngine Mounting Plate Frame423185X505 428684Idler ARM Bracket Impeller BeltTraction Belt Idler Pulley187833X428 Wheel Assembly LH187865X428 Safety Ignition KEY 193071DECAL, Danger 181037DECAL, DANGER, Deflector Service Notes Service Notes Limited Warranty