Poulan 429837, 96192003401 owner manual Loop Handle LH, Loop Handle RH, Lower Tube, Pivot Support

Page 26

REPAIR PARTS SNOW THROWER - - MODEL NUMBER XT827ES (96192003401)

HANDLES

4	4	KEY	PART
	4	NO.	NO.	DESCRIPTION
		NO.	NO.	DESCRIPTION
4		1	419798X479	LOOP HANDLE LH
	1	2	419799X479	LOOP HANDLE RH
3		3	74780524	SCREW 5/16−18 X 1.50
3		4	751153	NUT 5/16−18
4		4	751153	NUT 5/16−18
4
3
2

01.08.004-B

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	419797X479	LOWER TUBE
2	418313X479	PIVOT SUPPORT
3	428867	BOLT 5/16-18 X .750
4	17000616	SCREW 3/8-16 X 1.00

4	4

01.05.004-C

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 26

Image 26

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONParts Packed Separately in Carton Install Traction Drive Control ROD See Figs HOW to SET UP Your Snow ThrowerInstall Speed Control ROD See Figs Tool BOX See FigCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Primer OperationKnow Your Snow Thrower TractionMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See FigsTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig ADD Gasoline See FigIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Before Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting 23 22 KEY Part Description Auger 27 LH Auger HousingScraper BAR Auger 27 RHAuger Bearing Bearing PlugDeflector Seal Chute WeldmentDeflector Weldment StrapCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLower Tube Loop Handle LHLoop Handle RH Pivot SupportKnob RED SpacerRetainer Handle KnobShifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD BottomHeadlight Bezel Wire HarnessConsole Panel Flood HeadlightRepair Parts Snow Thrower - Model Number XT827ES Drive Wheel HUB Speed Selector AssemblyDrive Plate Assembly END PlateSprocket Axle ShaftRoll PIN 3/16 Clik PINEngine Mounting Plate Frame423185X505 428684Idler ARM Bracket Impeller BeltTraction Belt Idler Pulley187865X428 Wheel Assembly LH187833X428 Safety Ignition KEY 193071DECAL, DANGER, Deflector 181037DECAL, Danger Service Notes Service Notes Limited Warranty

REPAIR PARTS SNOW THROWER - - MODEL NUMBER XT827ES (96192003401)

HANDLES

KEY

LOOP HANDLE LH

LOOP HANDLE RH

KEY

LOWER TUBE

PIVOT SUPPORT