Poulan 429837, 96192003401 owner manual Parts Packed Separately in Carton, Assembly / PRE-OPERATION

Page 4

PARTS PACKED SEPARATELY IN CARTON

(1) AUGER CONTROL ROD

(1) MULTI-

WRENCH

(180684)

(2) FLAT WASHERS

	(1) POWER CORD
(1) DISCHARGE CHUTE	(198563)	(3) RETAINER
(1) DISCHARGE CHUTE

		SPRINGS
		(169675)

ROTATOR HEAD MOUNTING

(2) CARRIAGE BOLTS 3/8-16 x 2.25

SAFTEY IGNITION KEY (S) (193071)

(1) WASHER 3/8	(1) LOCKNUT 3/8
(19131316)	(73800600)

(2) HANDLE KNOBS

EXTRA SHEAR BOLTS AND NUTS

(2) SHEAR BOLTS 1/4-20 x 1-3/4	(2) LOCKNUTS
(192090)	1/4-20
	(73800400)

ASSEMBLY / PRE-OPERATION

Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly, operation and maintenance of the product.

Your new snow thrower has been assembled at the factory with the exception of those parts left unassembled for ship- ping purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag. To ensure safe and proper operation of your snow thrower, all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.

REMOVE SNOW THROWER FROM CARTON

1.Remove all accessible loose parts and parts boxes from carton.

2.Cut down all four corners of carton and lay panels flat.

3.Remove the two (2) screws securing the auger housing to the pallet.

4.Remove all packing materials except plastic tie holding speed control rod to lower handle.

5.Remove the two (2) plastic ties securing the upper handle to the pallet.

6.Remove snow thrower from carton and check carton thoroughly for additional loose parts.

4

Image 4

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONRemove Snow Thrower from Carton HOW to SET UP Your Snow Thrower Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Tool BOX See FigInstall Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Operation Know Your Snow ThrowerPrimer TractionMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See FigsUsing the CLEAN-OUT Tool See Fig To Adjust Skid Plates See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BAR See FigCheck Engine OIL Level See Fig ADD Gasoline See FigBefore Stopping Snow Throwing TipsIf Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting 23 22 KEY Part Description Auger Housing Scraper BARAuger 27 LH Auger 27 RHAuger Bearing Bearing PlugChute Weldment Deflector WeldmentDeflector Seal StrapLEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator HeadLoop Handle LH Loop Handle RHLower Tube Pivot SupportSpacer RetainerKnob RED Handle KnobImpeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD BottomWire Harness Console PanelHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number XT827ES Drive Speed Selector Assembly Drive Plate AssemblyWheel HUB END PlateAxle Shaft Roll PIN 3/16Sprocket Clik PINFrame 423185X505Engine Mounting Plate 428684Impeller Belt Traction BeltIdler ARM Bracket Idler Pulley187833X428 Wheel Assembly LH187865X428 Safety Ignition KEY 193071DECAL, Danger 181037DECAL, DANGER, Deflector Service Notes Service Notes Limited Warranty