Poulan 429837, 96192003401 owner manual Meets A.N.S.I. Safety Requirements

Page 8

OPERATION

GASOLINE

FILLER CAP

MUFFLER

CHOKE CON-

TROL

PRIMER

SAFETY

IGNITION

KEYON / OFF SWITCH

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

AUGERS

	ELECTRIC	AUGER	DISCHARGE CHUTE CONTROL LEVER
	START BUTTON	AUGER	DISCHARGE CHUTE CONTROL LEVER
	START BUTTON	CONTROL
		CONTROL
	RECOIL LEVER		DRIVE SPEED	TRACTION
	(AUXILIARY)		CONTROL LEVER	DRIVE
	STARTER			CONTROL
	HANDLE			LEVER
		CHUTE
	DEFLECTOR
				LIGHT
				DEFLECTOR
				CHUTE KNOB
	DISCHARGE
	CHUTE

	CLEAN-OUT TOOL	HANDLE
	CLEAN-OUT TOOL	KNOB
		KNOB
		MUFFLER
		TOOLBOX

SKID PLATE

FIG. 8

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button – used for starting the engine.

Recoil (auxiliary) starter handle – used for starting the engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Choke control - used for starting a cold engine. ON / OFF switch - used to STOP the engine.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power-pro- pelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the di- rection the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground.

8

Image 8

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONParts Packed Separately in Carton HOW to SET UP Your Snow Thrower Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Tool BOX See FigCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Operation Know Your Snow ThrowerPrimer TractionMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See FigsUsing the CLEAN-OUT Tool See Fig To Adjust Skid Plates See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BAR See FigCheck Engine OIL Level See Fig ADD Gasoline See FigIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting 23 22 KEY Part Description Auger Housing Scraper BARAuger 27 LH Auger 27 RHAuger Bearing Bearing PlugChute Weldment Deflector WeldmentDeflector Seal StrapLEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator HeadLoop Handle LH Loop Handle RHLower Tube Pivot SupportSpacer RetainerKnob RED Handle KnobImpeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD BottomWire Harness Console PanelHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number XT827ES Drive Speed Selector Assembly Drive Plate AssemblyWheel HUB END PlateAxle Shaft Roll PIN 3/16Sprocket Clik PINFrame 423185X505Engine Mounting Plate 428684Impeller Belt Traction BeltIdler ARM Bracket Idler Pulley187865X428 Wheel Assembly LH187833X428 Safety Ignition KEY 193071DECAL, DANGER, Deflector 181037DECAL, Danger Service Notes Service Notes Limited Warranty